Indesit GB IWDD 7123 사용 설명서 지침 - 페이지 3

{카테고리_이름} Indesit GB IWDD 7123에 대한 사용 설명서 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit GB IWDD 7123 16 페이지. Indesit washer/dryer user manual
Indesit GB IWDD 7123에 대해서도 마찬가지입니다: 사용 설명서 지침 (16 페이지), 사용 설명서 지침 (16 페이지)

페이지 인쇄

Connecting the drain hose

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

We advise against the use of hose extensions; in case

of absolute need, the extension must have the same

diameter as the original hose and must not exceed 150

cm in length.

Ensure that if the drain hose is pushed into a standpipe,

that the end does not go down more than 15cms (6 in-

ches). If the hose is pushed down too far, this may cause

the machine to self -syphon ie. continuously empty as it

is filling.

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

• the socket is earthed and in compliance with the

applicable law;

• the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

The drain hose may be

connected to an under-

sink trap. Before connec-

ting the drain hose from

the machine ensure that

any blanks or removable

ends have been taken off

the spigot.

If it is place over the edge

of a basin or sink be sure

the free end of the hose

should not be underwa-

ter.

• the supply voltage is included within the values i

ndicated on the Technical details table

(see page 5);

• the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate use.

Before using the appliance please read the instructions

below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse

cover re-fitted. If the fuse cover is lost, the plug must not

be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or the

colour that is embossed in words on the base of the plug.

Replacements can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and

you should wish to re-route the mains cable through parti-

tions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere re-wearable

plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable out-

let, controlled by a switch, (in compliance with BS 5733)

which is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally inserted

into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow Earth

Blue

Neutral

Brown

Live