Indesit IPG 640 S GB 사용 설명서 - 페이지 6

{카테고리_이름} Indesit IPG 640 S GB에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit IPG 640 S GB 16 페이지.
Indesit IPG 640 S GB에 대해서도 마찬가지입니다: 사용 설명서 (16 페이지), 사용 설명서 (12 페이지), 사용 설명서 (48 페이지)

페이지 인쇄

Hooking position

for top H=40mm

! Use the hooks contained in the "accessory pack".

• Where the hob is not installed over a built-in oven, a

wooden panel must be installed as insulation. This must

be placed at a minimum distance of 20 mm from the lower

part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet

must be removed. It is advisable to install the oven so that it

rests on two strips of wood, or on a completely flat surface

with an opening of at least 45 x 560 mm (see diagrams).

! The hob can only be installed above built-in ovens with a

cooling ventilation system.

Electrical connection

! THIS APPLIANCE MUST BE EARTHED.

The hob is designed to work with alternating current, the

supply voltage and frequency indicated on the rating plate

(situated under the hob). Make sure that the local supply

voltage corresponds to the voltage indicated on the rating

plate.

Connecting the supply cable to the mains electricity

supply

For models supplied without a plug, fit a standard plug

suitable for the load indicated on the rating plate, onto a

cable and connect to a suitable socket. To connect direct

to the mains supply, a double pole switch with a contact

separation of at least 3mm suitable for the load and

complying with current standards and regulations must be

fitted between the appliance and the mains supply outlet.

The green-yellow earth wire must not be interrupted by

the switch.

The supply cable must be positioned so that no part of it

reaches a temperature of 50°C above room temperature.

For installation above a built-under oven, the hob and the

oven must be connected separately to the electricity supply,

both for safetly reasons and for easy removal of the oven

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Front

Back

for repair, maintenance etc.

DO NOT use adapters as they could cause overheating

or burning.

Before connecting to the power supply, make sure that:

• the limiter switch and the domestic system can withstand

the load from the appliance (see rating plate).

• the supply system is efficiently earthed according to

standards and laws in force.

• the socket or double-pole switch are easily accessible

when the appliance is installed.

! The wires in the mains lead are coloured in accordance

with the following code:

Green & Yellow - Earth

Blue

- Neutral

Brown

- Live

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to terminal marked "E" or

or coloured Green or Green & Yellow.

Connect the Brown wire to the terminal marked "L" or

coloured Red or Brown.

Connect the Blue wire to the terminal marked "N" or coloured

Black or Blue.

FAILURE TO OBSERVE THE ACCIDENT-PREVENTION

REGULATIONS RELIEVES THE MANUFACTURER OF

ALL LIABILITY.

Replacing the cable

Use a rubber cable of the type H05RR-F with a suitable

cross section 3 x 0.75 mm².

The yellow-green earth wire must be 2-3 cm longer than

the other wires.

Gas connection

The appliance should be connected to the main gas supply

or to a gas cylinder in compliance with current national

regulations. Before carrying out the connection, make sure

the cooker is compatible with the gas supply you wish to

use. If this is not the case, follow the instructions indicated

in the paragraph "Adapting to different types of gas."

When using liquid gas from a cylinder, install a pressure

regulator which complies with current national regulations.

! Check that the pressure of the gas supply is consistent

with the values indicated in Table 1 ("Burner and nozzle

specifications"). This will ensure the safe operation and

longevity of your appliance while maintaining efficient

energy consumption.

Connection with a rigid pipe (copper or steel)

! Connection to the gas system must be carried out in such a

way as not to place any strain of any kind on the appliance.

There is an adjustable L-shaped pipe fitting on the appliance

supply ramp and this is fitted with a seal in order to prevent

leaks. The seal must always be replaced after rotating the

pipe fitting (seal provided with appliance). The gas supply

pipe fitting is a threaded 1/2 gas cylindrical male attachment.