Indesit IDC 75B K 지침 책자

{카테고리_이름} Indesit IDC 75B K에 대한 지침 책자을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit IDC 75B K 4 페이지.

페이지 인쇄

Instruction booklet

TUMBLE DRYER

This symbol reminds you to read this booklet

WHERE TO INSTALL THE TUMBLE DRYER

ranges, stoves, radiators or

hobs as flames may damage

it. If the dryer is installed

below a worktop, ensure

there are 10 mm between

the upper panel of the dryer

15 mm

and any objects above it and

15 mm between the sides of

the machine and the walls or

furniture units adjacent to it. This ensures adequate

air circulation.The appliance must be installed with

the rear surface placed against a wall.

! We do not recommend that the dryer is installed

in a cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door

with a hinge on the opposite side to that of the

dryer

door.

Priming the Water Collection System.

When your dryer is new, the water container will not collect water

until the system is primed. This will take 1 or 2 drying cycles. Once

primed it will collect water during every drying cycle.

WATER DRAINAGE CONNECTION

If the dryer is installed next to a drain the water can be plumbed into

this drain. This does away with the need

to empty the water container. The height

of the drain must be less than 1m from the

bottom of the dryer. Remove the existing

hose from the dryer and connect it to the

drain (if required add an additional length

of hose).

ELECTRICAL

CONNECTIONS

The socket must be grounded.

! The power cord must be regularly checked. If the

supply cord is damaged it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

BEFORE YOU START USING YOUR DRYER

Once you have installed your dryer and before

you use it clean the inside of the drum to remove

any dust that could have accumulated during

transport.

CONDENSER UNIT

You MUST clean the fluff from the condenser

EVERY month. Failure to clean the condenser

could cause premature failure of your dryer.

Remove the condenser unit regularly (at least

monthly) and clean off any fluff deposits.

IDC 75B (UK)

IDC 75B K (UK)

Install the dryer far from gas

IDC 75B S (UK)

IDC 75B X (UK)

Step 1

Open the condenser cover.

Step 2

Remove the condenser by turning

the 3 catches and

pulling the condenser

towards you. It is normal for some

residual water to be left in the

condenser unit.

Step 3

Flush the condenser

from the rear with water to remove

any fluff deposits.

Step 4

Replace the condenser unit and

make sure that all 3 catches are

closed and that the position arrows

on the front of the condenser are

pointing upwards.

FLUFF FILTER

You must clean the fluff filter after EVERY drying cycle.

Step 1

Open the door of your dryer.

Step 2

Pull out the filter (using the two

finger grips).

Step 3

Clean the fluff off the filter and

replace it correctly.

Step 4

Make sure the filter is pushed fully home - NEVER

run the dryer without the filter in position.

Failure to clean the filter after EVERY drying cycle

will affect the drying performance of your machine.

It will take longer to dry and as a result will use

more electricity during

WATER CONTAINER

You

MUST

empty the water container after

drying cycle. Removing the water container:

Step 1

Pull the water container

towards you and remove it

completely from the dryer.

Step 2

Empty all the water in the

water container.

Step 3

Replace the water container

making sure that it is securely fixed.

! Failure to empty the water container will

cause the machine to stop heating and the

load may still be wet at the end of the drying

cycle. The 'Empty Water' light will tell you that

the water container needs to

drying.

EVERY

be emptied