Indesit IDCE 845 A 사용 설명서 - 페이지 4

{카테고리_이름} Indesit IDCE 845 A에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit IDCE 845 A 20 페이지. Indesit clothes dryer user manual
Indesit IDCE 845 A에 대해서도 마찬가지입니다: 사용 설명서 (20 페이지), 사용 설명서 (20 페이지)

페이지 인쇄

Installation

Where to install the tumble dryer

• Install the dryer far from gas ran-

ges, stoves, radiators or hobs, as

flames may damage it. The dryer

should be installed in an ambient

room temperature of between 20

to 23°C for optimum performan-

ce. But will function if the room is

between 14 and 30°C.

If the dryer is installed below a

worktop, ensure there are 10 mm

between the upper panel of the

dryer and any objects above it,

and 15 mm between the sides of

the machine and the walls or furniture units adjacent to it. This

ensures adequate air circulation.

Ventilation

• The room must be adequately ventilated while the dryer is

running. Make sure that the dryer is installed in a room free of

humidity and with adequate air circulation. The flow of air around

the dryer is essential to allow water to condense during drying;

the dryer will not function properly if it is placed in an enclosed

space or inside a cabinet.

Some condensation may form if the dryer is used in a small or

cold room.

We do not recommend that the dryer is installed in a cupboard

but the dryer must never be installed behind a lockable door, a

sliding door or a door with a hinge on the opposite side to that of

the dryer door.

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container. If the dryer is stacked onto or

installed next to a washing machine it can share the same

drain. The height of the drain must be less than 3' (1 m)

from the bottom of the dryer. Remove existing hose from position

shown in picture A and fit a suitable length of hose and connect

as shown in picture B.

Make sure that the hose is not squashed or kinked

when the dryer is in its final location.

Picture A

Electrical connections

Before plugging the appliance into the socket, check the fol-

lowing:

• Make sure your hands are dry.

• The socket must have an earth connection.

• The socket must be able to withstand the machine's maxi-

mum power output as indicated on the data plate (see Descrip-

tion of the tumble dryer).

• The power supply voltage must fall within the values indicated

on the data plate (see Description of the tumble dryer).

• The socket must be compatible with the dryer's plug. Should

this not be the case, replace the plug or the socket.

Do not use extension cords.

The dryer must not be installed outdoors, even if the space is

sheltered. It can be very dangerous if exposed to rain or storms.

Once installed, the dryer's electrical wire and plug must be

within reach.

15 mm

Picture B

The power cord must not be bent or squashed.

The power cord is supplied fitted with a BS1363 plug and with

a 13 amp BS1362 fuse. If it is necessary to fit a replacement

fuse, it must be a 13 Amp ASTA approved to BS1362 type.

WARNING: The plug must not be used without a fuse cover. If a

replacement fuse holder/cover is required, it must be of the same

colour coding or wording as shown on the base of the plug.

Replacements are available from authorised dealers.

Moulded plug

Changing the plug

The wires in the power cord are coloured in accordance with the

following.

Green and Yellow (Earth)

wire to terminal marked "E",

GREEN &

symbol x, or coloured green

YELLOW

and yellow.

BROWN

BLUE

Blue (Neutral) wire to

terminal marked "N" or

coloured black.

If the plug being replaced is a non-rewirable type, then the cut-

off plug must be disposed of safely. DO NOT leave it where it can

be inserted into a socket and create a shock hazard.

The power cord should be checked periodically and replaced

by a cord specially prepared for this dryer and fitted only by

authorized technicians (see Service). New or longer power cords

are supplied at an extra charge by authorized dealers.

The manufacturer denies any responsibility should any of these

rules not be followed.

If in doubt about any of the above consult a qualified

electrician.

Levelling the tumble dryer

The dryer must be installed level for correct operation.

When you have installed your dryer in its final location check that

it is level first side-to-side, then front to back. If the dryer is not

level, adjust the two legs up or down until your dryer is level.

Preliminary information

Once the tumble dryer is installed, clean the inside of the drum

before operating it and remove any dirt accumulated during

transportation.

Warning ! Before you use your dryer ensure that its has

been in a upright position for at least 6 hours.

13A ASTA approved fuse to

BS 1362.

13 ampere fuse

CROSS-BAR

CORD GRIP

Brown (live) wire to teminal

marked "L" or coloured red.