Kohler 71120122-0 설치 및 관리 매뉴얼 - 페이지 4
{카테고리_이름} Kohler 71120122-0에 대한 설치 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Kohler 71120122-0 45 페이지.
![Kohler 71120122-0 설치 및 관리 매뉴얼](/uploads/products/server2/2613112/2613112.jpg)
Thank You For Choosing Sterling
We appreciate your commitment to Sterling value. Please take a few minutes to review
this manual before you start installation. If you encounter any installation or
performance problems, please don't hesitate to contact us. Our phone numbers are listed
on the back cover. Thanks again for choosing Sterling.
Merci d'avoir choisi Sterling
Nous apprécions votre engagement envers la qualité Sterling. Veuillez prendre s'il vous
plaît quelques minutes pour lire ce manuel avant de commencer l'installation. Ne pas
hésiter pas à nous contacter en cas de problème d'installation ou de fonctionnement. Nos
numéros de téléphone sont indiqués au verso. Merci encore d'avoir choisi Sterling.
Gracias por elegir los productos de Sterling
Le agradecemos que haya elegido a Sterling por la calidad que ofrece al mejor precio.
Dedique unos minutos para leer este manual antes de comenzar la instalación. En caso
de problemas de instalación o de funcionamiento, no dude en contactarnos. Nuestros
números de teléfono se encuentran en la cubierta posterior. Gracias nuevamente por
escoger a Sterling.
Before You Begin
CAUTION: Risk of product damage. Install the bath on an adequately
supported, level subfloor. The basin area requires no additional support when the
subfloor is level and square with the stud framing. Use shims for additional
support if the subfloor is uneven. Do not install the bath over open floor joists.
CAUTION: Risk of product damage. Do not remove the foam backing from the
wall surround sections. Wall surround sections are equipped with foam backing
to bring the back of the wall into contact with the regular stud framing. This
foam is not packing material.
CAUTION: Risk of property damage. Only apply 100% silicone sealant to the
areas where instructed to do so. Do not add silicone sealant to any other areas.
The inappropriate use of silicone sealant may trap moisture and could result in
mold, leakage, or mildew. For bath-only installations, 100% silicone sealant is
required at the seams of the walls and the bath. We recommend using colored
100% silicone sealant to match the color of the product. Use of latex based or
other caulks is not recommended. If a shower door will be added, you will be
instructed to apply silicone sealant where the front edges of the end wall
surrounds will meet the bath. This will prevent water from passing through the
shower door extrusion to the back side of the wall. Follow the shower door and
silicone sealant manufacturer's instructions.
CAUTION: Risk of product damage. Do not lift the bath using the apron brace.
Lift the bath by the rim at multiple points. Bath units in a single carton are
shipped with apron braces in the closed position. Bath units in multi-pack
cartons are shipped with one or more sets of apron braces disconnected at the
apron. Connect the apron braces to the apron before removing the unit from the
carton(s).
CAUTION: Risk of product damage. To avoid rust marks on your product,
ensure the roofing nails or non-tapered flathead screws are galvanized or plated.
If using galvanized or plated non-tapered flathead screws, do not overtighten
the screws. Excessive tightening can damage the wall flange. Consult local
building codes to determine if the screws or nails must be galvanized or plated.
IMPORTANT! If your bath is shipped with a liner, keep the liner in place until
construction is complete to prevent surface damage to the unit. If a liner is not
available, place a clean drop cloth or similar material in the bottom of the bath.
Read all instructions before you begin.
Observe all applicable plumbing and building codes.
1064910-2-A
4
Sterling