Kohler Escale K-25091T-S 설치 지침 매뉴얼 - 페이지 20
{카테고리_이름} Kohler Escale K-25091T-S에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Kohler Escale K-25091T-S 23 페이지. Floor standing toilet
Kohler Escale K-25091T-S에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (11 페이지), 설치 지침 매뉴얼 (28 페이지), 설치 지침 매뉴얼 (30 페이지)
페이지 인쇄
TROUBLESHOOTING
Please make following checks before repair:
Symptoms
No flushing
(Indicator not flashing)
No flushing or poor
flushing while the indicator
can flash
Keep flushing indicator not
flashing
Battery indicating light
keeps flashing and no
flushing
If the trouble remains after above-mentioned actions are taken, please contact with us via distributor.
简单故障排除
请在委托修理前做以下检查：
现象
不出水
（感应指示灯不亮）
感应指示灯闪烁
而无水流出或出水较差
不停水
感应灯也不闪烁
电池指示灯连续
闪烁而不出水
如按以上操作仍未解除故障，请通过销售商与本公司联系。
1350669-T01-A
Probable causes
1. No power or mistake connected.
2. Ther e is an object within the sensing distance.
3. The sensing window needs cleaning.
4. The toilet seat is loose.
5. The toilet cover (if applicable) is closed.
6. Around squat is dirty.
1. Adjusting bolt not fully open.
2. Low water pressure.
3. Filter is obstructed.
1. There are some dirty materials inside the valve
body.
2. The manual unit is damaged.
Out of electricity.
(Only for K-30947T-CP/BN,K-30951T-CP/BN)
可能原因
1. 无电源或接线有误。
2. 感应范围内有其它物体一直被感应。
3. 感应窗口较脏。
4. 座便器座圈松动。
5. 座便器盖合上（若有）。
6. 蹲便器周围太脏。
1 .
调节栓未完全打开。
2 .
水压太低。
3 .
过滤装置脏堵。
1 .
阀体部件内有脏物。
2 .
手动装置损坏。
电池耗尽（仅适用于安装K-30947T-CP/
BN,K-30951T-CP/BN的情况）。
Corrective actions
1. Check the power connect.
2. Remov e the object or reduce the sensing
distance.
3. Clean the window.
4. Fasten the toilet seat, and follow the
steps for automatic adjustment of the
sensing distance again.
5. Open the toilet cover.
6. Clean the squat.
1. Open the adjusting bolt.
2. Improve water supply.
3. Clean the filter.
1. After cleaning the filter, activate the
sensor several times.
2. Check the manual unit.
Replace batteries.
(Only for K-30947T-CP/BN,K-30951T-CP/BN)
处理方法
1. 检查电源连接。
2. 清理物体。
3. 清洁窗口。
4. 紧固座圈，并重新按自动调距步骤操作。
5. 打开座便盖。
6. 清洁便器周围。
1 .
打开调节栓。
2 .
改善供水情况。
3 .
清洗过滤装置。
1 .
清洗过滤装置后，使感应器连续感应动作
数次。
2 .
检查手动装置。
更换新电池(仅适用于安装K-744T-M的情况)。
14