Kohler Command PRO CH26 소유자 매뉴얼 - 페이지 9

{카테고리_이름} Kohler Command PRO CH26에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Kohler Command PRO CH26 21 페이지. Command series
Kohler Command PRO CH26에 대해서도 마찬가지입니다: 소유자 매뉴얼 (21 페이지), 소유자 매뉴얼 (21 페이지), 소유자 매뉴얼 (8 페이지), 소유자 매뉴얼 (21 페이지), 소유자 매뉴얼 (14 페이지)

페이지 인쇄

Maintenance Schedule

These required maintenance procedures should be performed at the frequency stated in the table. They should

also be included as part of any seasonal tune-up.

Frequency

Daily or Before

Starting Engine

Every 25 Hours

Every 100 Hours

Every 200 Hours

Every 250 Hours

Annually or

Every 500 Hours

Every 1500 Hours

Perform these maintenance procedures more frequently under extremely dusty, dirty conditions.

Have a Kohler Engine Service Dealer perform this service.

Cleanout Kits 25 755 20-S (black) or 25 755 21-S (gold) allow cooling areas to be cleaned without removing shrouds.

Only required for Denso starters. Not necessary on Delco starters.

Check Oil Level

The importance of checking and maintaining the

proper oil level in the crankcase cannot be

overemphasized. Check oil BEFORE EACH USE as

follows:

1. Make sure the engine is stopped, level, and is cool

so the oil has had time to drain into the sump.

2. To keep dirt, debris, etc., out of the engine, clean

the area around the dipstick before removing it.

3. Remove the dipstick; wipe oil off. Reinsert the

dipstick into the tube and press all the way

down.

4. Remove the dipstick and check the oil level.

The oil level should be up to, but not over, the "F"

mark on the dipstick. See Figure 7.

Operating

Range

Figure 7. Oil Level Dipstick.

Maintenance Required

• Fill fuel tank.

• Check oil level.

• Check air cleaner for dirty

• Check air intake and cooling areas, clean as necessary

• Service precleaner element

• Replace air cleaner element

• Change oil. (More frequently under severe conditions.)

• Remove cooling shrouds and clean cooling areas

• Check oil cooler fins, clean as necessary (if equipped).

• Check spark plug condition and gap.

• Change oil filter.

• Replace fuel filter (carbureted engines).

• Replace heavy-duty air cleaner element and check inner element

• Have bendix starter drive serviced

• Have solenoid shift starter disassembled and cleaned

• Have crankshaft spline lubricated

• Replace fuel filter

(EFI engines).

"F" Mark

, loose, or damaged parts.

1,3

2,4

5. If the level is low, add oil of the proper type, up to

the "F" mark on the dipstick. (Refer to Oil Type on

page 5.) Always check the level with the dipstick

before adding more oil.

NOTE: To prevent extensive engine wear or

damage, always maintain the proper oil

level in the crankcase. Never operate the

engine with the oil level below the "L"

mark or over the "F" mark on the

dipstick.

Oil Sentry™

Some engines are equipped with an optional Oil

Sentry™ oil pressure switch. If the oil pressure

decreases below an acceptable level, the Oil Sentry™

will either shut off the engine or activate a warning

signal, depending on the application.

NOTE: Make sure the oil level is checked BEFORE

EACH USE and is maintained up to the "F"

mark on the dipstick. This includes engines

equipped with Oil Sentry™.

2,4