Kohler Courage SV730 소유자 매뉴얼 - 페이지 11

{카테고리_이름} Kohler Courage SV730에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Kohler Courage SV730 21 페이지. Vertical crankshaft
Kohler Courage SV730에 대해서도 마찬가지입니다: 소유자 매뉴얼 (21 페이지), 소유자 매뉴얼 (8 페이지)

페이지 인쇄

NOTE: Operating the engine with a blocked grass

screen, dirty or plugged cooling ﬁns, and/or

cooling shrouds removed, will cause engine

damage due to overheating.

Ignition System

These engines use an electronic Capacitive Discharge

(CD) ignition system. Other than periodically

checking/replacing the spark plugs, no maintenance,

timing, or adjustments are necessary or possible with

this system.

Check Spark Plugs

Every 100 hours of operation, remove the spark plugs,

check condition, and reset the gap or replace with new

plugs as necessary. The standard Courage spark plug

is a Champion

RC12YC (Kohler Part No.

12 132 02-S). RFI compliant engines use a Champion

XC12YC (Kohler Part No. 25 132 14-S) spark plug. A

high-performance spark plug, Champion

3071 (Kohler Part No. 25 132 12-S) is standard on

Courage PRO models. Equivalent alternate brand

plugs can also be used.

1. Before removing the spark plug, clean the area

around the base of the plug to keep dirt and

debris out of the engine.

2. Remove the plug and check its condition. Replace

the plug if worn or reuse is questionable.

NOTE: Do not clean the spark plug in a machine

using abrasive grit. Some grit could remain in

the spark plug and enter the engine causing

extensive wear and damage.

3. Check the gap using a wire feeler gauge. Adjust

the gap to 0.76 mm (0.030 in.) by carefully

bending the ground electrode. See Figure 14.

4. Reinstall the spark plug into the cylinder head.

Torque the spark plug to 24.4-29.8 N·m

(18-22 . lb.).

Wire Gauge

Spark Plug

Ground

Electrode

Figure 14. Servicing Spark Plug.

Platinum

0.76 mm

(0.030 in.) Gap

Battery Charging

WARNING: Explosive Gas!

Ba eries produce explosive hydrogen gas while being

charged. To prevent a ﬁre or explosion, charge ba eries only

in well ventilated areas. Keep sparks, open ﬂames, and other

sources of ignition away from the ba ery at all times. Keep

ba eries out of the reach of children. Remove all jewelry

when servicing ba eries.

Before disconnecting the negative (-) ground cable, make

sure all switches are OFF. If ON, a spark will occur at the

ground cable terminal which could cause an explosion if

hydrogen gas or gasoline vapors are present.

Fuel System

Fuel Filter

Some engines are equipped with an in-line fuel ﬁlter.

Periodically inspect the ﬁlter and replace with a

genuine Kohler ﬁlter every 100 operating hours.

Fuel Line

In compliance with CARB Tier III Emission

Regulations, these engines use Low Permeation

SAE 30 R7 rated fuel line; certiﬁed to meet CARB

requirements. Standard fuel line may not be used.

Order replacement hose by part number through a

Kohler Engine Service Dealer.

Figure 15. Low Permeation Fuel Line.

Carburetor Troubleshooting and

Adjustments

In compliance with government emission standards,

the carburetor is calibrated to deliver the correct

fuel-to-air mixture to the engine under all operating

conditions. The high speed mixture is set at the factory

and cannot be adjusted. The low idle fuel adjustment

screw (if equipped) is also set at the factory and

normally does not require adjustment. See Figure 16.

Engines in this series depending on the model and

application, may also be equipped with a Governed

Idle System.

If the engine is equipped with a Governed Idle

System, refer to Models with Governed Idle System

when performing any carburetor adjustment, as an

additional step to the listed procedure(s) is required.