2N Telekomunikace 2N SmartCOM 빠른 매뉴얼

{카테고리_이름} 2N Telekomunikace 2N SmartCOM에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 2N Telekomunikace 2N SmartCOM 2 페이지.

페이지 인쇄

Read the User Manual carefully to get familiar with all system functions.

Security Precautions

 Do not switch on 2N

medical apparatuses to avoid interference. The

minimum distance of the antenna and pacemakers

should be 0.5m.

 Do not switch 2N

chemical facilities or sites where explosives are

used.

 Any mobile telephone use prohibition based on RF

energy radiation applies to 2N

 2N

SmartCOM may disturb the function of TV sets,

radio sets and PCs.

 Warning! 2N

SmartCOM contains components that

can be swallowed by small children (SIM card,

antenna, etc.).

 When 2N

SmartCOM comes to the end of its

operational life, dispose of it in accordance with

applicable regulations.

 2N

SmartCOM is equipped with an external

antenna connector. The antenna has to be located

indoors for safety reasons.

Basic Functions

 2N

SmartCOM is designed for bidirectional data

transmission between serial ports and their

opponents based on GPRS data transmission

via the GSM network.

Installation Conditions

 Install the GSM antenna with respect to the

signal quality in the location.

 Keep 2N

SmartCOM off sensitive devices and

human bodies to avoid EM interference.

External Antenna Connection

Screw the enclosed antenna into the SMA

antenna

connector.

connector gently with your hand, never use a

tool!

SIM Card Installation

Insert the SIM card in the hole in the upper part of

SmartCOM making sure that the bevelled

edge of the SIM card faces the green connector

(see the figure on the front side of the product).

Remember to set the relevant provider's services

(PIN request off, e.g.) on your mobile phone before

inserting the SIM card in 2N

LED Statuses

No light

3x fast flash

Slow blinking

Very fast blinking

Continuous light

SmartCOM Quick Guide

SmartCOM in the vicinity of

SmartCOM aboard a plane.

SmartCOM near petrol stations,

SmartCOM too.

Tighten

the

antenna

SmartCOM.

Device not supplied

Start or restart

Connecting to network, starting GPRS session

Error: wrong PIN or SIM not inserted

Connected, IP address assigned (flashes when transmitting data)

SmartCOM

following:

SmartCOM

Antenna

Supply adapter

 Do not place the unit near heat sources

(such as

heaters,

necessary.

 2N

under the conditions specified in the

operating

unauthorised

changes in use and operation may

result in malfunction or destruction of

the product.

sure that the provider's SIM card is intended for the

GSM network supported by your 2N

version and that the GPRS data transmission is

activated with an IP address enabling incoming

connection (unless you use the SmartCOM server)

Power Supply

SmartCOM is DC supplied from a 12V/0.5A

power adapter included in the delivery. The use

any

SmartCOM. Do not connect the power

supply until you have connected the antenna to

avoid the GSM module damage!

Initialisation

Once you connect the power supply, the GSM

module, inputs, outputs, serial interfaces and

configuration

SmartCOM can be regarded as functional if

the GSM connection and IP address assignment

LED indicator keeps shining constantly. Refer to

the LED Statuses table below for initialisation

and operation details.

Make

delivery

space heaters, hot air

etc.)

unless

SmartCOM only works reliably

instructions.

interventions

other

adapter

may

module

will

get

contains

the

1 pc

absolutely

Any

and/or

SmartCOM

damage

initialised.