Aqua Computer aquagraFX 설치 및 사용자 설명서

{카테고리_이름} Aqua Computer aquagraFX에 대한 설치 및 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Aqua Computer aquagraFX 1 페이지. Graphics card waterblock

페이지 인쇄

aqua

computer

Description

Thank you for purchasing a graphics card

waterblock manufactured by Aqua Computer. The

aquagraFX for GTX 680 Lightning has been

specifically designed for graphics cards according

to reference design of the chip manufacturer. The

aquagraFX for GTX 680 Lightning effectively cools

the RAM, voltage regulators and GPU of your

graphics card. The base part of the waterblock is

manufactured from pure copper for outstanding

performance and durability.

Installation

Step 1:

Remove the originally installed air cooling unit

from the graphics card. The procedure necessary

to perform this might slightly vary depending on

the graphics card. Use extreme caution not to

damage any of the highly sensitive components of

the graphics card! Disconnect the fan connector

while lifting the air cooling unit off the graphics

card.

Step 2:

Remove all thermally conductive pads from the

graphics card and clean all surfaces with direct

contact to the cooling unit from remaining thermal

compounds using benzine if necessary.

Apply a thin layer of thermal compound to the

GPU and the RAM modules. These components

are marked red in the figure. The thermal

compound must not be electrically conductive! Cut

fitting pieces from the thermally conductive pad

supplied with the aquagraFX and place them on

Installation and user manual aquagraFX for GTX 680 Lightning, 08/2012

top of the voltage regulators as indicated by green

rectangles.

Step 3:

Attach the aquagraFX for GTX 680 Lightning to the

graphics card. The original back plate will be

reused. At first carefully and evenly screw in the

four screws adjacent to the GPU (four screws M3 x

4 mm), afterwards the remaining screws (five

screws M3x6 mm). Secure the lateral areas of the

back plate with four screws M3 x 6 mm and fittings

hex nuts M3 supplied with the aquagraFX.

Step 4:

Carefully check that the waterblock has level

contact to all relevant components of the graphics

card. Do not power on the graphics card or the

PC if the cooler does not perfectly fit the graphics

card! In this case, disassemble and repeat the

mounting procedure. All screws must not be overly

tightened to prevent the PCB from twisting!

Step 5:

Insert the graphics card to your PC and integrate

the waterblock into your cooling system. Be sure

Aqua Computer GmbH & Co. KG – Gelliehäuser Str. 1 – D-37130 Gleichen

not to connect any waterblocks in parallel but only

consecutively. A detailed instruction on building a

watercooling system and plug&cool connectors as

well

can

found

www.aqua-computer.de

– please check the section

support/download.

Step 6:

Put the water cooling system into operation, but do

not connect any other PC components to the

mains supply! Check the waterblock as well as the

fittings for leakages and do not put your PC into

operation unless you can definitively eliminate the

possibility of coolant leaking from the system! If

any component has been in contact with coolant,

do not put it into operation before it is completely

dry again! For operating the graphics card, the

waterblock must be correctly mounted and be

connected to a water cooling system featuring

adequate cooling performance! For corrosion

inhibition, either Double Protect Ultra or a mixture

of water and ACfluid according to the preparation

instructions provided with ACfluid must be used as

coolant!

ATTENTION:

Disregarding the instructions may lead to severe

damages! Aqua Computer GmbH & Co. KG

cannot be held liable for damages or injuries

resulting from improper installation or use of the

product!

Thank you again for choosing an aqua computer

product.

our

website