Dexter Laundry T1200 설치 및 작동 지침 - 페이지 8
{카테고리_이름} Dexter Laundry T1200에 대한 설치 및 작동 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Dexter Laundry T1200 18 페이지. 75lb capacity computer control opl washer
Dexter Laundry T1200에 대해서도 마찬가지입니다: 설치 및 운영 매뉴얼 (18 페이지), 소유자 책자 (16 페이지)
페이지 인쇄
PROGRAMMING INSTRUCTIONS:
Programming can be accomplished manually using the machine controls or by connecting to the
machine control using a PDA (personal digital assistant). For instructions on using a PDA with
this washer control, please contact your local Dexter distributor. Please read below for manual
programming instructions.
The washer has two levels of programming. The Coin/Price Programming allows the owner to
set the price for the washer features and the values of the coins. The Washer Cycle Programming
allows the owner complete access to the wash cycle parameters – add/remove a bath, bath times,
spin times, water temperatures, etc. To enter the programming modes, the top of the washer must
be unlocked and slid toward the back of the washer a few inches.
COIN PRICE PROGRAMMING
While the washer is in the Idle mode, push the Programming pushbutton on the controller. The
Idle mode is when the washer is not running a cycle and the price of the bath is displayed. The
Programming pushbutton is a very small button located on the upper center of the controller
directly behind the display. There are seven stages in the Coin/Price Programming mode.
To step through to the desired stage, repeatedly push the START button until the desired
stage is blinking on the display. To exit the Coin/Price programming mode, push and hold
the Cold temperature button for 5 seconds.
Stage 1: Right Coin – The display will blink first an "r" indicating right coin and then a coin
value ($1.00 – default). The display will blink back and forth between the "r" and the value. To
change the value, use the Hot temperature button to decrease and the Warm temperature button
to increase. The value will change in 1¢ steps. The range of values is from $00.00 to $99.99.
When the desired right coin value is displayed, push the Start button once to store the new value
and a second time to move to the next Coin/Price programming step.
To exit the Coin/Price programming mode, push the Cold temperature button for 5 seconds.
Stage 2: Left Coin – The display will blink first an "L" indicating left coin and then a coin value
($0.25– default). The display will blink back and forth between the "L" and the value. To
change the value, use the Hot temperature button to decrease and the Warm temperature button
to increase. The value will change in 1¢ steps. The range of values is from $00.00 to $99.99.
When the desired left coin value is displayed, push the Start temperature button once to store the
new value and a second time to move to the next Coin/Price programming step. To exit the
Coin/Price programming mode, push the Cold temperature button for 5 seconds.
Stage 3: Wash Price – The display will blink first a "P" indicating wash price and then present
wash price. The display will blink back and forth between the "P" and the price. To change the
value, use the Hot temperature button to decrease and the Warm temperature button to increase.
The value will change in 1¢ steps. The range of values is from $00.00 to $99.99. If the wash
price is set to $00.00, the display will show "FREE" after exiting the programming mode. When
the desired price is displayed, push the Start button once to store the new value and a second
time to move to the next Coin/Price programming step. To exit the Coin/Price programming
mode, push the Cold temperature button for 5 seconds.