Avocent Emerge MPX1500 빠른 설치 매뉴얼

{카테고리_이름} Avocent Emerge MPX1500에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Avocent Emerge MPX1500 1 페이지. Multipoint high-definition (hd) wired/wireless extender system
Avocent Emerge MPX1500에 대해서도 마찬가지입니다: 기술 사양 (2 페이지), 빠른 설치 매뉴얼 (2 페이지), 브로셔 (2 페이지), 브로셔 (8 페이지), 사양 (2 페이지), 빠른 설치 매뉴얼 (2 페이지)

페이지 인쇄
Avocent Emerge MPX1500 빠른 설치 매뉴얼
The following instructions will allow you
to set up your AutoView switching
system easily.
Should you require assistance, please
consult your installer/user guide.
1
Turn off your systems and
attach the appropriate
power cord.
To connect the AutoView

switch hardware:

1
Connecting power to the AutoView switch
Turn off all computers that will be attached to your
AutoView switch. Plug the supplied power cord into the
AutoView switch power socket on the rear of the unit.
Plug the other end into an appropriate AC power source.
2
Connecting the analog ports
Plug your VGA monitor, keyboard and PS/2 mouse
cables into analog user port sets A and/or B located on
the rear of the AutoView switch.
3
Connecting an AVRIQ module or Integrated
Access Cable (IAC) module to the AutoView switch
Choose an available port, labeled 1-8 or 1-16, located
on the rear of the AutoView switch. For an AVRIQ module,
To Contact Avocent Technical Support
Avocent, the Avocent logo, AutoView and The Power of Being There are registered trademarks of Avocent Corporation or its affiliates. All other marks are the property of their respective owners. ©2005 Avocent Corporation. All rights reserved.
Quick Installation Guide
AutoView
For models: 1400, 1500 or 2000
To configure the AutoView switch
5
Turn on the servers,
switches and the
Configuration Port
AutoView switch.
for updating firmware
2
Plug in the keyboard,
monitor and mouse
cables for your analog
station connections.
Analog User A
plug one end of a CAT 5 cable (up to 32.8 feet or 10 meters),
into anumbered port and plug the other end into the RJ-45
connector on the AVRIQ module. For an IAC module, plug
the CAT 5 connector into a numbered port.
4
Connecting a server to an AVRIQ or IAC module
Plug the AVRIQ or IAC module keyboard, monitor and
mouse connectors into the appropriate ports on the back
of either a server or a compatible switch. Repeat this
procedure for all servers that are to be connected to the
AutoView switch.
CALL (888) 793-8763
VISIT www.avocent.com/support
®
Switch
Analog User B
AutoView 2000 Switch
1
2
3
Connect an AVRIQ or
IAC module to one of the
available ports.
4
Connect servers or
switches with servers
to an AVRIQ module
(shown below) or an
IAC module.
AVRIQ Modules or IACs
PS/2, USB, Sun and serial
AVRIQ modules are
available. PS/2 and USB
IAC modules are available.
DOWNLOAD Check out the latest software from our web site at www.avocent.com
3
5
7
9
11
13
15
4
6
8
10
12
14
16
Servers 2-16
Server 1
5
Turning on the servers and switches
While the components can be turned on in any order,
we recommend turning on the servers first and then
all other switches.
For additional information
For further information, please refer to the AutoView
1400/1500/2000 Installer/User Guide included with
the switch. Check http://www.avocent.com for the latest
software and firmware updates.
590-508-501A