Avocent SwitchView SC4 UAD 빠른 설치 매뉴얼
{카테고리_이름} Avocent SwitchView SC4 UAD에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Avocent SwitchView SC4 UAD 2 페이지. Usb secure desktop switching
Avocent SwitchView SC4 UAD에 대해서도 마찬가지입니다: 빠른 설치 매뉴얼 (4 페이지), 사양 (2 페이지)
페이지 인쇄
The following will help you install your
SwitchView SC4 UAD switch easily.
Should you require further assistance, please
contact Avocent Technical Support.
1
Connecting local peripherals
Turn off all servers that will be part of your
SwitchView SC4 UAD switching system. Locate
your USB keyboard, DVI monitor, USB mouse,
speakers and microphone. Plug your DVI monitor
cable into the appropriate CONSOLE port on
the left side of the back of your switch. Plug your
USB keyboard cable and your USB mouse cable
into the keyboard and mouse ports respectively.
Plug your speaker cable and microphone cable
into the corresponding ports.
2
Connecting your servers
Locate your first cable set consisting of one USB
cable, one DVI cable and two audio cables. The
SwitchView SC4 UAD switching system has four
port sets labeled A-D on the rear of the unit. Plug
the USB cable, the two audio cables (speaker
and microphone) and the DVI cable (monitor)
into the corresponding ports on your server.
Plug the other ends into any of the available server
port sets on your SwitchView SC4 UAD switch.
Repeat this process until all servers are properly
attached to the SwitchView SC4 UAD switch.
NOTE: Cable sets without audio cables are
available if you do not require speaker and
microphone support.
3
Powering your system
Locate the power cord that came with your
To Contact Avocent Technical Support: Visit www.avocent.com
Avocent, the Avocent logo, The Power of Being There, the Cybex logo and SwitchView are registered trademarks of Avocent Corporation or its affiliates. ©2007 Avocent Corporation. All rights reserved.
Quick Installation Guide
SwitchView
DVI/USB Switch with Audio
To install the SwitchView SC4 UAD switch
4
Optional
RF ground
(not required for
safety)
1
switch. Plug one end into the IEC power connector on
the SwitchView SC4 UAD switch. Ensure the power
switch is off, then plug the other end of the power
cord into an AC wall outlet. Turn on your switch first,
then turn on all attached servers.
4
Switching your servers
Press the appropriate front panel button labeled A-D to
access servers in your SwitchView switching system.
LEDs
Each target port (A-D) has a single bi-color LED on the front
panel. The LED will be green when the target device is on
and connected to the switch. The LED will change to amber
when the target device is selected (KVM session).
Mechanical
H x W x D = 1.75" x 11" x 11" (4.44 x 27.94 x 27.94 cm)
Weight = 4.9 lbs (2.2 kg)
The Power of Being There
SC4 UAD
®
2
Environmental
Operating Temperature: 41˚ (5˚C) to 104˚ (40˚C)
Storage Temperature: -4˚ (-20˚C) to 122˚ (50˚C)
Input Power: 60 W; Operating Voltage 100-240 VAC
Power Frequency: 50-60 Hz
Supported Hardware
Server: IBM, Sun, PC/AT, USB and 100% compatibles
Video Modes: VGA, SVGA, XGA, SXGA, UXGA,
WVGA, WSVGA, WXGA, WSXGA, WUXGA,
and HDTV
Maximum resolution: Single link DVI up to
1920 x 1200 @ 60Hz (monitor and video card support
for the maximum resolution will vary and should be
verified for compatibility)
Peripherals: USB keyboard, USB mouse and
IntelliMouse (USB only)
®
3
590-609-501B