Avocent Advanced Console Server ACS 6000 릴리스 정보 - 페이지 12
{카테고리_이름} Avocent Advanced Console Server ACS 6000에 대한 릴리스 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Avocent Advanced Console Server ACS 6000 15 페이지. Universal management gateway
페이지 인쇄
Event log time stamps are not adjusted when the time zone is changed until after an appliance reboot.
When moving time within the appliance forward and then logging out, the appliance may reject further
logins. Please reboot the appliance to restore normal operation.
An incorrect error message is displayed when an invalid DHCP range is entered in the Dynamic Ranges
table of the /Administration/Targets/Port Configuration/DHCP Settings screen.
A Service Processor Discovery log and the Event log Export functions provide a .CSV file that uses '|'
separators instead of ','.
The Avocent® Universal Management Gateway 2000 appliance does not update the Event Viewer Log
page when switching to a different page and back to the Event Viewer Log page. The Event Viewer Log
page will reload when the Next button is clicked to advance to the next page of Event Log, then the Prev
button is clicked to return to the original Event Log page.
The Avocent® Universal Management Gateway 2000 appliance does not currently support filtering of
events shown on the Event Viewer Log pages. The events can be filtered by exporting the Event Log and
then filtering the events using a separate tool.
If the Web browser cache history is cleared during an active Web interface session, an HTTP request error
will occur on the next Web interface screen refresh. If this occurs, please close the browser window and log
in to the appliance Web interface again.
Browsing in the Web interface consumes memory in the client browser that is not returned. Please close
the browser session to recover client memory.
Web interface sessions cannot be established using the Internet Explorer 8.0.6001.18702 (Cypher
Strength 128-bit). Please upgrade to Internet Explorer 8.0.7601.17514 (Cypher Strength 256-bit), or a
newer version of Internet Explorer to support this functionality.
If the appliance is configured for an IPv6 network, Web interface sessions cannot be established using the
Firefox browser version 25 or later. Please use an alternate browser to access the appliance.
Web interface sessions cannot be established on some clients using Firefox browser version 31. Please
browse to the about: support page and Reset Firefox, then try to establish the session again after the
browser restarts.
Asset Location
Due to a Methode CCM limitation, the CCM must be power-cycled when it is disconnected from one
Avocent® Universal Management Gateway appliance before it is reconnected to another Avocent®
Universal Management Gateway appliance.
KVM/UMIQ Module
On a heavily utilized Avocent® Universal Management Gateway appliance, a KVM session may fail with
the path is blocked or Resource could not be located error.
A second KVM session launch from the appliance Web interface to the same UMIQ on an appliance from
the same client will fail. Please use the DSView™ 4 software interface if this function is required.
If UMIQ module targets are lost after rebooting an appliance, it is suggested to disable the Automatically
Delete Offline Modules setting in the Admin-Targets-KVM Management-Default Settings page.
It may be necessary to enable then re-disable mouse acceleration before the mouse pointer can be
synchronized with a Linux
A target computer with a video resolution less than 1400 x 900 and a screen refresh of 70 Hz cannot be
scaled to a higher KVM resolution.
When using the DSView™ 4 software and moving a UMIQ module from one port to another port on the
Avocent® Universal Management Gateway appliance, the appliance must be resynced in the DSView™ 4
software to correctly update the port. Also, if the Automatically Delete Offline Modules configuration is
selected, delay at least ten seconds between disconnecting the UMIQ module from the appliance before
reconnecting it to a different port.
machine.
12