Avocent MergePoint SP5324 빠른 설치 매뉴얼

{카테고리_이름} Avocent MergePoint SP5324에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Avocent MergePoint SP5324 2 페이지. Service processor (sp) manager
Avocent MergePoint SP5324에 대해서도 마찬가지입니다: 사양 시트 (2 페이지), 빠른 설치 매뉴얼 (2 페이지)

페이지 인쇄

MergePoint

QUICK INSTALLATION GUIDE

The following instructions will help you install your

MergePoint service processor manager. Should you require

further assistance, please contact Avocent Technical Support.

Rack mounting or placing the MergePoint SP

manager

When installing the MergePoint SP manager in a rack,

note the MAC address printed on the bottom label of the

appliance.

Connecting power to the MergePoint SP

manager

Verify the appliance power switch is off. For AC models,

plug the power cord into the appliance and plug the other

end into a grounded AC power source. For DC models,

wire the terminal block to separate DC power sources.

Turn on the power switch. For more information on wiring

DC models, see the MergePoint SP53XX SP Manager

Installer/User Guide.

NOTE: For appliances with two power supplies, connect

each supply to a separate power source.

Connecting to the network

Connect an Ethernet cable from the primary

10/100/GE (Gigabit Ethernet) port to the network. To

conﬁ gure a secondary 10/100 Ethernet port, including

setting up failover, see the installer/user guide.

Conﬁ guring the MergePoint SP manager IP

addresses

The MergePoint SP manager requires an IP address

before use. The MergePoint SP manager ships as a DHCP

client, and can obtain an IP address from a DHCP server.

If you are using a DHCP server, proceed to step 5.

-or-

If your network environment does not have a DHCP server

or if the DHCP server is not available or times out, two

default IP addresses are automatically designated for eth0

and eth1. The IP addresses are 192.168.0.10 for eth0,

and 192.168.0.20 for eth1. If you wish to designate an IP

address, conﬁ gure the appliance via a DSView

or the Command Line Interface (CLI).

To conﬁ gure using the DSView 3 software:

Use the DSView 3 Add Units Wizard to add the

MergePoint SP manager to the DSView 3 software.

During the Add Unit Wizard, select Unit does not have

IP address. Enter the MergePoint SP manager network

information and select the unit MAC address from the list.

To conﬁ gure using the CLI:

Connect a terminal or a server running a terminal

emulation program to the console port using the included

DB-9 to RJ-45 crossover cable.

a. Open a terminal session with the settings: ANSI

emulation, 9600, 8, N, 1, no ﬂ ow control.

b. Log in as root and use the default password Sydney.

c. Enter the passwd command and change the root

password.

WARNING: For maximum security, the default username

and password should be changed.

d. Enter the cli command.

e. Enter network speciﬁ c information with the set

command. For example, to activate the primary

Ethernet interface, conﬁ gure a static IP address and

basic network parameters, enter:

set network interface eth0 method static address <IP_

address> netmask <netmask> gateway <gateway>

Technical support and ﬁ rmware or software updates:

Product manuals:

www.avocent.com/manuals

Avocent, the Avocent logo, MergePoint and DSView are registered trademarks of Avocent Corporation or its afﬁ liates in the U.S. and other countries. All other marks are the property of their respective owners. ©2008 Avocent Corporation.

SP5324/SP5340

Service Processor (SP) Manager

MergePoint SP5340 Service Processor Manager Shown

Blade or Service Processor (SP)

NOTE: Pressing the Tab key twice will list available

command variables.

f. Enter the commit command to save changes.

g. Enter the quit command to exit the cli utility.

h. Log out.

3 server

Using the conﬁ guration wizard

The ﬁ rst time you log in to the MergePoint SP manager,

the conﬁ guration wizard window opens automatically.

The wizard allows you to conﬁ gure appliance settings

such as alias, default user account, discovery range,

appliance network, provisioning, SNMP and host table

among others. These settings can be saved as an XML

ﬁ le for future use when you conﬁ gure an appliance using

the wizard. See the MergePoint SP53XX SP Manager

Installer/User Guide for more information.

(Optional) Connecting service processors to the

MergePoint SP manager

NOTE: The MergePoint SP manager can administer

service processors connected to the same physical

network it resides on. For maximum security, connect

service processors directly to the MergePoint appliance

private network ports.

Connect a standard Ethernet cable from any private

Ethernet port on the MergePoint appliance to any of the

following types of Ethernet ports:

• A dedicated Ethernet port on a service processor

• A dedicated Ethernet port on a blade server

managing multiple blade service processors

Conﬁ guring the service processor

Using your service processor's documentation, enable the

service processor and assign it an IP address.

www.avocent.com

Remote User

Ethernet

Network

Console User

CAUTION: Depending on your system conﬁ guration,

service processors that are not connected directly to

the MergePoint SP manager may be accessible from

a public network. To prevent unauthorized access, it is

recommended that you change the preset username and

password for the service processor.

Conﬁ guring the DSView 3 software

If you wish to host service processors on multiple

subnets, you can conﬁ gure them through the DSView 3

software or MergePoint SP manager web interface. See

the installer/user guide for details.

Conﬁ guring private subnets

At least one subnet is required to allow SPs connected

to the private Ethernet ports to communicate with the

MergePoint SP manager.

Conﬁ gure an IP address for the private subnet. The

MergePoint SP manager uses this IP address to

communicate with the service processors.

After conﬁ guring a private subnet, it is recommended that

the administrator assign each SP an IP address within

the range of the private subnet. If an SP is not assigned

an address with the range of the private subnet, the

MergePoint SP manager attempts to contact the SP using

the primary interface IP.

Multiple private subnets are not required, but may be

used.

NOTE: The MergePoint SP manager does not normally

route between the private subnets. The private subnets

are an added layer of security and separation between

connected service processors.

(Continued on reverse side)

590-838-501C