Avocet CYCLOMETER 15 빠른 시작 매뉴얼 - 페이지 4

{카테고리_이름} Avocet CYCLOMETER 15에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Avocet CYCLOMETER 15 4 페이지.

페이지 인쇄

STEP 1– RECEIVER.

Cut the clamp screw

off the receiver bracket with scissors. Position

the receiver on the right fork blade about 3"

above the hub. The receiver housing should be

parallel to a spoke positioned behind it. Insert

the screw and tighten it until the receiver stays

in position on the fork.

Receiver

Clamp Screw

SPECIFICATIONS

nstrument displays either miles or kilometers.

Speed Functions

SPEED: To 75 mph

Maximum Speed (MX): To 75 mph (resettable)

Average Speed (AV): To 75 mph. Calculated only

while the wheel is turning. Averages up to 10 hours

(resettable)

Resolution of speed functions: 0-19.9 mph, to 0.1; 20-

39.5 mph, to 0.5; 40-75 mph, to 1.0

Distance Functions

Total Distance (D): To 6,210 mi in 0.1 mi increments.

Display rolls over at 6,210 miles

Trip Distance (d): To 621.00 mi in 0.01 mi increments

Time Functions

Riding Time (ST): To 9:59:59 (time used to compute

average speed). At 10:00:00 rolls over and resumes

timing

Stopwatch ( ST ): To 9:59.99 in 0.01 second increments

then to 9:59:59 in 1.0 second increments. At

10:00:00 rolls over and resumes timing . When

stopped displays to 0.01 second

Clock: 24 hour format; to 1 minute

INSTALLATION

STEP 2 – TRANSMITTER.

Remove the

screw from the transmitter magnet and install it

on one of the right-side spokes opposite the re-

ceiver. The magnet should line up over one of

the marks on the receiver and not align between

the marks.

Rotate the receiver until it is

" from the

transmitter magnet. Tighten the transmitter and

receiver screws. Trim off excess receiver clamp

strap with scissors.

Spoke

Screw

Transmitter

Align transmitter with

the upper or lower mark

Setup functions

Miles/Kilometers: Stored data converted when

setup is changed

Wheel Size Calibration: Calibration for wheels

from 100 mm (4") circumference to 2,999 mm

(118") circumference in 1 mm increments

Automatic Power Saver: Displays clock only

(Cyclometer 25) or blank screen (Cyclometer 15) to

cut power consumption by 50% while retaining

stored data

Dimensions: 1.75" X 1.75" x 0.3"

Weight: Unit, 0.5 oz

Display: Dual liquid crystal, UPPER NUMBERS

0.3" high; lower numbers 0.2" high

Operational Temperature Range: 0°F to 150°F

Battery: 1.35 volt, approximately 2 year life. Use

Avocet Cyclometer 15/25 battery or Eveready AC

675E, Duracell DA675, Panasonic PZ675P, Varta

V675A, or Ray-O-Vac 675A

STEP 3 - RECEIVER WIRE.

Attach the

wire to the inside of the fork with cable ties,

then wrap the wire around the front brake cable

until the excess has been used up. Attach the

wire only to parts that rotate when the bicycle

is steered–the fork, handlebar stem, or the front

brake cable. Do not attach the wire to the head

tube.

Brake Cable

Tie

Receiver

AVOCET 1-YEAR LIMITED WARRANTY

Your Avocet Cyclometer is warranted against defects in material and workmanship for one year after

manufacture. Defective products will be repaired or replaced. The warranty does not cover the battery,

normal wear, damage, or loss, and is void if the unit is disassembled by anyone other than an Avocet

Authorized Service Center. The US Authorized Service Center is:

AVOCET, INC

World Wide Web WWW.AVOCET.COM

STEP 4 – MOUNT BRACKET.

rubber shim around the handlebar near the

stem. Remove the clamp screw and place the

bracket on the handlebar over the shim. If the

shim is too long, trim it shorter with scissors.

Insert the clamp screw and tighten it until the

bracket is secure. Slide the Cyclometer into the

bracket from front to rear until it snaps on. Spin

the wheel and confirm that a speed reading is

displayed. If the display remains at zero, check

that the receiver and transmitter magnet are

aligned and

" apart.

Avocet Service Center

170A Universt\ity Ave

Palo Alto, CA 94301

650-470-0478 ext 218

Wrap the