Avon AC1240IC 지침 및 정보 설명서 - 페이지 5

{카테고리_이름} Avon AC1240IC에 대한 지침 및 정보 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Avon AC1240IC 5 페이지. Electronic smart charger

페이지 인쇄

SUMMARY OF OPERATION:

Step 1

Pulse charging

Connect the charger to the

battery, the charger will detect

12V STD

the

battery's

mode

automatically.

(1) If a voltage of more than 7.5

V is detected, the charger

recognizes battery as 12V

(2) If a voltage of 7.5V-10.5V is

12V AGM

found, maintenance charge is

mode

activated ( 0.8A pulse charging

until voltage exceeds 10.5V)

(3) If the voltage doesn't reach

10.5V within 30minutes, a

12V

battery fault is indicated.

Winter

mode

Connect the charger to the

battery, the charger will detect

the

battery's

automatically;

(1) If voltage of less than 7.5V

detected

the

recognizes the battery as 6V

(2) If voltage of 1.5V-5V is

STD

found, maintenance charge is

mode

activated ( 0.8A pulse charging

until voltage exceeds 5.25V)

(3) if voltage doesn't reach

10.5V within 30minutes, a

battery fault is indicated

TROUBLESHOOTING

Display

Battery polarity reversal symbol

displayed.

Clamp indication and voltage symbols

displayed

No Display

Display back light on, display showing

0.0V and clamp symbol.

Output lead fuses should be checked and replaced as necessary (5A blade) in connection with all faults. Also check the fuse in the

mains plug, which should only be replaced with a 3A BS1362 fuse.

Persistent fuse replacement may indicate a fault with the charger or leads. Check these before each use and do not use if worn or

damaged.

DECLARATION OF CONFORMITY

We declare that this product conforms to the following standards EN60335-1, EN60335-2-29, EN55014, EN61000,

and the following Directives 73/23 CEE, 93/68 CEE, 2004/108/EC, 2002/95/EC (ROHS)

Technical Manager

Bristol Batteries Ltd, November, 2015

Step 2

Step 3

Soft

Auto-Select Current & Bulk

start

Charging

Every 15-20min the

charger will check the

voltage

battery voltage. If the

voltage has increased by

0.2V or more the charging

current will remain the

same.

charging

If the voltage has not

until the

increased by 0.2V the

voltage

charger will increase the

reaches

charging current by 1 Amp.

12.8V

to 2A. The cycle will be

repeated every 15-20min.

and the charging current

can be increased to 3A or

4A. This charging cycle will

continue until the battery

voltage reaches the

maximum value.

Every 15-20min the

charger will check the

voltage

battery voltage. If the

voltage has increased by

0.2V or more the charging

charger

charging

current will remain the

until the

same.

voltage

If the voltage has not

reaches

increased by 0.2V the

6.4 V

charger will increase the

charging current by 1 Amp.

to 2A. The cycle will be

repeated every 15-20min.

and the charging current

can be increased to 3A or

4A. This charging cycle will

continue until the battery

voltage reaches 7.2V

Fault

Battery clamps reversed

Dirty or oxidized battery terminals. Low or

unstable charging current

Mains supply not connected

Battery not connected

Step 4

Absorption

14.4V constant

Maximum

Charging current

voltage

steps down by 1A at

14.4V

a time until 1Amp is

14.8V constant

Maximum

voltage Charging

voltage

current steps down

14.8V

by 1A at a time until

1Amp is reached

14.8V constant

Maximum

voltage Charging

voltage

current is falling until

14.8V

Maximum

voltage; Charging

voltage

current steps down

7.2V

by 1A at a time until

1Amp is reached

Step 5

Float charging

Charger will detect

the battery's voltage

voltage

again

(1) If the voltage falls

below 12V. Battery

fault is shown.

reached

(2) If voltage is

12-13.2V, charger will

switch to

maintenance

charging

(3) If the voltage is

more than 13.2V

charger will wait for

the voltage to fall

before starting a

maintenance charge.

Charger will detect

the battery's voltage

again

(1) If the voltage falls

below 6V. Battery

fault is shown.

(2) If the voltage is

7.2V constant

6-6.6V, charger will

switch to

maintenance

charging.

(3) If the voltage is

more than 6.6V

charger will wait for

the voltage to fall

before starting a

maintenance charge

Action

Disconnect & reconnect correctly

Clean terminals

Check socket

Check clamps, replace battery