Billi Quadra 설치 매뉴얼 - 페이지 8
{카테고리_이름} Billi Quadra에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Billi Quadra 8 페이지. Xl, xt, xr tap options
Billi Quadra에 대해서도 마찬가지입니다: 사용자 설명서 (13 페이지), 사용자 설명서 (12 페이지), 설치 매뉴얼 (7 페이지)
페이지 인쇄
Commissioning
XL, XT, XR.
INSTALLATION AND
COMMISSIONING CHECKLIST
Filter packing foam removed
from under filter cannister.
Dispenser mounted securely – M4
chrome retaining screw fitted.
Dispenser swivels 45º in each direction
(if activated) - locking piece is removed.
Tubing is cut to correct lengths and
not kinked or sagging. Red, grey and blue
silicone tubes have a continual fall.
Tubing not twisted or kinked.
Tubing secured correctly – nuts and
spring clips.
Water main flushed before connection to
unit.
Unit connected to COLD water supply.
Correct air clearances around unit.
Power circuit fitted with an RCD
– earth leakage protection device.
Sawdust cleaned out of cupboard area.
Door vents fitted correctly (air-cooled
models only).
Initial program settings correctly set
for dispenser tube length.
Time (check if daylight savings),
day and date set correctly – Refer to
Quadra User Guide.
Unit heating and cooling (after initial fill).
Red and blue dispenser icons flashing
(or on continually when reached correct
temperature).
Boiling and chilled water flow correct.
If any difficulties arise contact
Billi Pty Ltd: Phone 1800 812 321 (Free call).
Validate your warranty online at
www.billi.com.au
For information on our filtration
and service contracts please contact
Billi Customer Service on 1800 812 321
Billi Pty Ltd
42 Lucknow Crescent, Thomastown
Victoria 3074 Australia
Telephone 1800 812 321
Facsimile +61 3 9469 0499
www.billi.com.au
8
WARNINGS.
For continued safety of this appliance
it must be installed, operated and
maintained in accordance with the
manufacturer's instructions.
— Your appliance should be installed by
a suitably qualified tradesperson.
— For correct operation of this appliance
it is essential to observe the instructions
as outlined in this booklet.
— Do not use this appliance with water
that is microbiologically unsafe or with
water of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may
be used on disinfected water that may
contain filterable cysts.
— Filter replacement must be performed
at intervals of not more than 12 months.
— Use this appliance only as directed in
these instructions and only for its designed
purpose.
— This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
— Children should be supervised to ensure
that they do not play with the appliance.
— DANGER: The operation of the thermal
cut-out indicates a possibly dangerous
situation. Do not reset the thermal cut-out
until the water heater has been serviced
by a qualified person.
— WARNING: Do not connect any restrictor
or pressure relief device to the vent pipe
of this water heater if installed.
— If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
— New hose-sets supplied with the appliance
are to be used and old hose-sets should
not be re-used.
Designed and manufactured in Australia.
As Billi Pty Ltd has a policy of continual
improvement, all details are subject
to change without notice. All goods
are sold subject to our published terms
and conditions. Billi is a registered
trademark. 0217