Billi Sahara Plus 설치 매뉴얼 - 페이지 3

{카테고리_이름} Billi Sahara Plus에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Billi Sahara Plus 7 페이지.
Billi Sahara Plus에 대해서도 마찬가지입니다: 설치 매뉴얼 (8 페이지), 사용자 설명서 (12 페이지)

페이지 인쇄

Installing the

dispenser.

IMPORTANT: This Billi appliance is to be installed by a licensed tradesperson in accordance with

AS 3500.4 or AS/NZ 3500.4.2 and in compliance with applicable state regulatory requirements.

For correct operation of this appliance, it is essential to observe the manufacturer's instructions.

1. Install Dispenser Assembly

Determine position of dispenser mounting

hole in sinktop or benchtop. Dispenser

base template (Diagram 3) may be cut

out and used to assist in correct positioning.

Refer to Diagram 2 for clearances allowed.

Hole size required is ø32mm.

—Stainless Steel Sinktop

A suitable 32mm hole punch (Part no: 857901)

is available as an accessory from Billi Pty Ltd.

If possible, cut hole with die mounted below

the sinktop surface so that burr is pulled

downwards. Alternatively, remove burr and

radius edge of hole with fine file. This allows

barbed dispenser mount to slide smoothly

into mounting hole. Oil hole punch regularly.

Lubricate surface to be cut with detergent.

—Timber/Laminate Benchtop

Maximum benchtop thickness is 50mm

Cut 35mm hole in appropriate position*.

When drilling through a particle board bench

top, take care to avoid a large chip breaking

away as drill breaks through underside

surface. We recommend drilling a small

pilot hole through benchtop, partially drilling

the 35mm hole from underneath and then

completing drilling the hole from above.

The large 30mm washer supplied may

be used to secure barb where underside

particle board bench top has chipped away.

* For granite or marble benchtops we

recommend you use a certified stone

mason to pre-drill the hole.

2. Activate Dispenser Swivel Feature

To activate the swivel feature of your

dispenser, you will need to remove the

locking piece from the dispenser base.

Simply push out the piece as show in

Diagram 4. This will allow the tap to

move 45 degrees to the left and right.

3. Fit Dispenser Base

a. Cut a 32mm hole in sinktop or benchtop.

Remove burr if protruding upwards.

b. Push barbed mounting shaft through

mount hole.

c. Insert barb locking bush as shown

in Diagram 5. Finger tighten nut.

d. Ensure barb is centred in mount hole

before tightening. Check position of

base ring and gasket.

e. Moderately tighten locking nut using

multigrips or spanner. Take care to avoid

overtightening nut which may break the

plastic threaded shaft.

Place large washer over thread as

shown in Diagram 6.

g. Cut off excess threaded shaft with a

hacksaw, using washer as a cutting guide.

IMPORTANT: Remove burrs and check internal

bore is completely smooth.

4. Fit Dispenser Head Assembly

a. Lay dispenser head assembly alongside

mounting base assembly.

b. Feed dispenser tubing and loom through

centre hole in the following order:

i. Dispenser power cord.

ii. Grey vent silicone tube. Feed tube

until reducing join passes through

mount assembly – see Diagram 7.

iii. Red and blue silicone tubing.

To assist feeding the tubing, we

recommend using silicone spray

lubricant. Gently pull hoses from

under the bench top, do not attempt

to force tubing through with a pointed

object as silicone tube is easily

punctured. Check tubing is not

kinked or twisted.

c. Turn dispenser head assembly to

approximately 60° from the straight

ahead position of dispenser base.

Slide head assembly onto base assembly

whilst gently pulling tubing downwards

from underneath to prevent tubing

bunching and kinking. Mounting lugs

will pass nut and slide down the 3

grooves on the swivel bearing.

d. Once fully down, turn dispenser to

straight ahead position. Fit chrome

plated M4 retaining screw to lower

rear threaded hole and tighten using the

allen key supplied. Check dispenser now

swivels smoothly 45° in each direction.

dispenser base

template

Locking Nut

Base Casting

Ensure burr is

remover & edge

is radiused

Barbed

Mounting

Shaft

Barb locking bush in position

Remove burrs after cutting and

ensure internal bore is smooth

Cut off

excess

thread

Silicone

tubing

Diagram 3

Diagram 4

Swivel

Bearing

Gasket

Washer if

required

Diagram 5

Washer

Diagram 6

Diagram 7