Aqua One Arctic 3/5HP 사용 설명서 - 페이지 4

{카테고리_이름} Aqua One Arctic 3/5HP에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Aqua One Arctic 3/5HP 6 페이지.

페이지 인쇄

Installation

1. Place the chiller in a well ventilated, level area.

2. The chiller is supplied with 19mm inlet and outlet

hosetails. Attach the hose to the inlet fitting. Use the

supplied hose clamp to secure the hose. The water

being supplied to the chiller should be pre-filtered to

avoid buildup in the internal pipes.

3. Attach the hose to the outlet fitting. Use the supplied

hose clamp to secure the hose. The outlet should not

be placed close to the pump that is feeding the

chiller.Use the supplied hose clamp to secure the

hose. The water being supplied to the chiller should be

pre-filtered to avoid buildup in the internal pipes.

4. Attach the hose to the outlet ﬁtting. Use the supplied

hose clamp to secure the hose. The outlet should not

be placed close to the pump that is feeding the chiller.

5. Turn on the water supply to the chiller. Allow it to run

for a few minutes before turning the chiller on at the

power supply.

6. Check all hoses and connections for any kinks or

leaks.

7. Plug the chiller in at the power supply.

8. There is a power switch located at the back of the

unit. Switch on the chiller.

9. Set the chiller to the desired temperature. Press

and hold the set button (ﬁg. 1) on the control pad for

5 seconds, until the display ﬂashes displaying P and

a 2 digit number. This is the temperature the chiller

is set to. Use the up and down buttons to select the

desired temperature. Once the correct temperature is

displayed, press the set button again.

The switching temperature can be set to a variance

of either 1, 2 or 3°C. In order to change this, press

the Set and Up arrow buttons (ﬁg. 2) together for 5

seconds. Either a 1, 2 or 3 will be displayed. Use the

up or down keys to switch between these settings then

press Set to conﬁrm the value. The chiller will turn on

once the temperature reaches this value above the

set temperature and switch off once the aquarium

temperature is below the set temperature. For example

if the chiller is set to 25°C with 2°C variance, the chiller

will switch on at 27°C and switch off at 24.9°C.

NOTE: If installing the chiller on an existing aquarium,

drop the temperature by only 1-2°C per day.

If the chiller is switched off it will take a minimum of 3

minutes for it to come back on.

Maintenance

When performing any maintenance on this unit,

ensure the power has been switched off at the power

supply and the plug has been disconnected.

It is recommended to clean the intakes on the chiller

once a month. Failure to do so may cause the chiller

to overheat and suffer permanent damage. In order to

clean the unit, remove the plastic covers then using

a soft bristled brush, throughly brush the entire grill.

Vacuum the area to remove any dust/dirt that has come

loose.

CAUTION: When cleaning the chiller, do not use water

on the external parts or the radiator. The chiller must

remain dry at all times.

If the chiller has not been run for an extended period

(for example after being switched off during winter),

ﬂush the chiller with freshwater or freshly mixed salt

water. Discard the water that is ﬂushed out of the unit.

CALIBRATION

This unit can be calibrated to ±1.5°C from the displayed

temperature. Calibration should be done using an

accurate thermometer and can be used to calibrate the

chiller to aquarium temperature where heat is generated

in water before it is supplied to the chiller, for example

by heaters or pumps. To calibrate the temperature press

and hold the Up and Down buttons (ﬁg. 3) together for

5 seconds. A temperature of between -1.5°C and 1.5°C

will be displayed. Use the Up and Down buttons to set

the desired calibration value then press the set button

to conﬁrm the value.

Fig, 1

Fig. 2

Fig. 3