Aqua Optima AWD001 사용 설명서 - 페이지 4
{카테고리_이름} Aqua Optima AWD001에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Aqua Optima AWD001 8 페이지.
Aqua Optima AWD001에 대해서도 마찬가지입니다: 사용 설명서 (8 페이지)
페이지 인쇄
Preparing a new fi lter
•
Remove all packaging from the water fi lter.
•
Do not worry about the black carbon particles on the packaging or fi lter, they are harmless.
•
Wipe the outside of the water fi lter with a damp cloth.
•
Don't use washing liquid, or anything that might leave a taint.
•
For the fi lter to perform at its best, all air bubbles must be removed before use.
•
Submerge the water fi lter in a bowl of cold water and shake it
gently. When no more bubbles are released, the water fi lter is ready for use.
•
You might see black carbon particles in the water. Again, don't worry as they are harmless.
Removing the old water fi lter
•
Use the handle to lift the lid off the fi lter holder (Fig.1)
•
Removing the fi lter holder will need two hands – put the thumbs inside the walls of the fi lter
holder, put the fi ngers on the outside of the rim, and gently lift upwards.
•
Don't turn the fi lter holder upside down. Try to keep the fi lter upright at all times.
•
Grip the bottom of the fi lter with the other hand.
•
Turn the fi lter clockwise (about 1.5cm), to bring the tabs on the top of the fi lter into the bulges
at the sides of its holder, then bring the fi lter down and out of the fi lter holder.
•
Gently ease the seal off the underside of the water tank (Fig.3)
•
Clean the seal and water tank with a damp cloth. Don't use washing-up liquid, or anything that
might leave a taint.
•
Fit the seal snugly to the underside of the fi lter holder. The lugs in the bottom of the fi lter holder
fi t into the slots in the seal (Fig.3).
Fit the new fi lter
•
Align the tabs on the top of the fi lter with the bulges on the underside of the fi lter holder.
•
Lift the fi lter up and into its holder, push it gently against the seal, and turn it anticlockwise
(about 1.5cm) to lock it into the fi lter holder.
•
Lower the fi lter holder into the water tank.
Fill the water tank
•
Lift the lid off the fi lter holder (if it's not already off).
•
Use a jug to pour water into the fi lter holder. If you don't have a big enough jug, clean out your
electric kettle and use that – most kettles hold about 1.7litres. Two jugs, two kettles, or a jug and
a kettle makes life even easier.
* Don't pour directly on to the fi lter.
Air Locks
•
To prevent air locks in the cooling unit (underneath the water tank) you need to keep the tap
open while you're fi lling the water tank, so that the incoming water drives the air out before it.
•
Put a container that holds at least a litre under the spout.
•
If the container is tall enough, use it to push the tap back against the wall of the cooler. If not
you'll have to hold the tap open with a fi nger.
•
Either way, push the tap back against the wall of the cooler and keep it there.
•
Pour water into the top of the fi lter holder.
•
Keep pouring untill about
•
That should be enough to clear all air out of the system.
•
With the tap closed, keep pouring into the fi lter holder until the water tank is full, and the fi lter
holder is full to within about a centimeter of the rim.
•
Water fl ow through the fi lter will get slower, as the water tank and the fi lter fi ll up.
•
Put the lid on – the edges of the lid should be just clear of the water.
AWD001 - Water dispenser_IM.indd 4
AWD001 - Water dispenser_IM.indd 4
to litre comes out of the spout, then let the tap close.
3.
2/13/2008 3:27:05 PM
2/13/2008 3:27:05 PM