Aqua Power DH 80 작동 및 설치 지침 매뉴얼 - 페이지 6

{카테고리_이름} Aqua Power DH 80에 대한 작동 및 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Aqua Power DH 80 15 페이지.

페이지 인쇄
Aqua Power DH 80 작동 및 설치 지침 매뉴얼

Technical Data

Model
1
Item No.
Design
Current
208 V
220 V
230 V
240 V
Recommended circuit
breaker size
2
Wire gauge, copper
3
Minimum water flow to
activate unit
Minimum water pressure to
activate unit
Max. working pressure
Volume of water in unit
Weight
Dimensions
(H x W x D)
Plumbing connections
Suitable for supply with cold water
1
2
This is our recommendation as the manufacturer. Check local codes for compliance if necessary. Tankless water heaters are considered a non-continuous load.
Copper must be used. Conductors should be sized to maintain a voltage drop of less than 3% under load.
3

Troubleshooting

Symptom
No hot water
The unit is not being switched on, elec-
tric supply and flow available
Water not hot enough
WARRANTY
Make any warranty claim in the country where you purchased the appliance. In such cases, please contact our representation
or the importer.
Our warranty applies only if:
– These installation instructions have been observed
– Exclusively accessories designated for this appliance have been used
– All required steps up to and including commissioning have been carried out by a qualified contractor
– Maintenance as specified has been carried out
– Exclusively our spare parts have been used for repairs

Environment and recycling

Please help us protect the environment. Dispose of the appliance and its packaging in accordance with national regulations.
DH 60
DH 80
227259
227329
Pressure type
Single phase - 60/50
Hz
5.5
/ 25
7.3
kW
A
6.0
/ 26
8.0
kW
A
6.5
/ 27
8.7
kW
A
30
40
A
10
8
AWG
0.76–0.92
0.85–1.0
gpm
2.9–3.5
3.2–3.8
l/min
3
/ 0.2
4.4
psi
bar
150
/ 10
psi
bar
0.13
/ 0.5
gal
l
3.44
/ 1.56
lb
kg
13
" / 350
x 7
" / 210
¾
¼
mm
mm
G ½"
Cause
- water flow too low to activate
flow switch.
- shower head is blocked with dirt
or lime
- circuit breaker off
- safety thermal cut-out tripped
- the minimum flow to activate unit
has not been achieved.
- filter in cold water connection
line blocked
- water flow too high
- heat setting too low
DH 100
234029
/ 33
8.4
kW
A
/ 35
9.2
kW
A
/ 36
10.0
kW
A
50
A
A
6
AWG
AWG
0.92–1.1
gpm
3.2–4.0
l/min
/ 0.3
4.4
psi
bar
x 3
" / 100
¾
mm
DH 100 C
234030
9.36
kW
/ 38
Not available
kW
A
/ 40
Not available
kW
A
/ 42
Not available
kW
A
50
A
6
AWG
0.92–1.1
gpm
3.4–4.0
l/min
/ 0.3
4.4
psi
bar
psi
Solution
- increase flow volume
- clean shower head or remove
lime scale
- turn breaker on
- reset thermal cut-out
- increase flow volume
- clean the filter screen after
shutting of the cold water supply
- reduce water flow
- turn temperature control knob to
the right (max. position)
/ 45
A
gpm
l/min
/ 0.3
bar