Allied Telesis x900-48 series 기능 설명서 - 페이지 6

{카테고리_이름} Allied Telesis x900-48 series에 대한 기능 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Allied Telesis x900-48 series 18 페이지. Configuring hardware filters
Allied Telesis x900-48 series에 대해서도 마찬가지입니다: 데이터시트 (5 페이지)

페이지 인쇄

The logic of the operation of the hardware filters

The operation of the filters follows the standard ACL logic: if a packet matches an filter, the

comparison process stops and the action attached to the filter is performed. If a packet fails

to match any of the filters, then the default action (forward) is taken.

Note:

The effects of the action parameters

Let us consider the effect of each the possible action keywords.

Action

discard

forward

copy

copy,discard

setl2qos

Note that this action has the other parameters associated with it, as the following syntax shows:

This action means you can use hardware filters to set the queue, 802.1p user priority or bandwidth class for packets.

There is an elaborate QoS mechanism available for allocating these values to packets, but this filter type provides a

simple method if you do not require a full QoS configuration. The principle use for this filter action, though, is as a

mechanism for elevating the probability of CPU reception for packets that you determine to be "important".

In heavily congested networks, data streams can sometimes use up all the available bandwidth of the CPU receive

process. This increases the probability of losing infrequently-sent control or management packets, for example,

routing protocol packets (BGP, OSPF, PIM, DVMRP) or STP packets. By creating an appropriate classifier and

hardware filter, such packets can be given higher priority forwarding up to the CPU.

If you are using the filter to prioritise packets going up to the CPU, you only need to specify a value for the

l2qosqueue parameter. The higher the value given to this parameter, the higher the priority the matching packets

will be given in forwarding up to the CPU. It is possible to specify the priority and bandwidthclass parameters

in this case, but they will have no effect, because the CPU ignores these parameters. The default value for the

l2qosqueue parameter is 0.

The priority parameter specifies the 802.1p user priority with which to re-mark matching packets. The default is 0.

The bandwidthclass parameter specifies the bandwidth class (colour) to assign matching packets to. The default

is 1 (green).

Page 6 | AlliedWare™ OS How To Note: Hardware Filters

Hardware filters will act on packets that are destined for the switch itself (packets

that would be passed up to the switch's own CPU) in exactly the same way as they

act on packets that were destined to be forwarded directly by the switching chip.

What it does

Drops the traffic.

Forwards the traffic normally.

Forwards the traffic normally, and

also sends a copy of each packet to

the CPU.

Drops the traffic, but also sends a

copy of each packet to the CPU.

add switch hwfilter[=<filter-id>] classifier=<rule-id> action=setl2qos

[l2qosqueue=0..7] [priority=0..7] [bandwidthclass=1..3]

Creating dedicated hardware filters

When do you need this action?

Use this when the filtering policy is to disallow certain

traffic flows.

Use this when you want to discard a wide range of traffic,

but still forward some small subset of traffic within that

range.

Use this when you want software monitoring of a certain

packet flow. If you want to log, or count, or output debug

pertaining to a certain stream, then create a filter that

matches the packets in the stream, and specify copy for

the action.

Use this when you want software monitoring of a certain

packet flow that is being dropped. If you want to log,

count, or output debug pertaining to a certain disallowed

stream, then create a filter that matches the packets in the

stream, and specify copy,discard for the action.