Avtech AVT420A 사용자 설명서 - 페이지 4
{카테고리_이름} Avtech AVT420A에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Avtech AVT420A 8 페이지. Hd cctv total solution
Avtech AVT420A에 대해서도 마찬가지입니다: 사용자 설명서 (6 페이지)
페이지 인쇄CAMERA PARAMETERS
On the DVR, right-click to show the main menu, and go to "ADVANCED CONFIG" "DCCS".
In "DCCS", select the channel which connects this camera, and click "SETUP" to enter the menu of camera
parameters.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DCCS
NOTIFY
MULTICASTING
EXIT
Item
BRIGHTNESS
CONTRAST
HUE
SATURATION
CAMERA GUARD
SEQUENCE
WHITE BALANCE
SHARPNESS
SLOW SHUTTER
MIRROR
FLIP
DENOISE
EXPOSURE VALUE
WIDE DYNAMIC RANGE
FIXED SHUTTER
DEFOG
IR CONTROL
IR TURN ON LEVEL
IR EXTEND TIME
RESET DEFAULT
REBOOT THE SYSTEM
CH1
CH2
CH3
MENU
SETUP
DEVICE
AVT503S
CONNECTION
OK
Description
Click the current value to manually adjust the brightness of the image. The higher the value,
the brighter the image.
Click the current value to manually adjust the contrast of the image. The higher the value,
the higher the contrast ratio.
Click the current value to manually adjust the hue of the image.
Click the current value to manually adjust the saturation of the image. The higher the value,
the more saturated the image.
Enable "GUARD LOCK" to temporarily disable the pan function of this camera and fix the
camera surveillance area.
For details, please refer to the section "CAMERA GUARD".
Configure a sequence group for area patrol.
For details, please refer to the section "MOTORIZED PAN AND SEQUENCE SETUP".
Process the current image to retain color balance over a color temperature range.
The options are: Auto, 2500K, 3200K, 4200K, 5800K & 9500K.
Sharpness enhances the clarity of image detail by adjusting the aperture and sharpening the
edges in the pictures.
Hold and drag the slider to adjust the level of sharpness. The higher the value, the sharper
the image.
Slow shutter is used to increase the exposure time to get clearer image, for example, at night.
The options are: AUTO, 1/15 and 1/6.
Select "ON" to rotate the images horizontally based on your installation situation when
necessary.
Select "ON" to rotate the image 180° when necessary.
Click and drag the slider to adjust the level from 0 ~ 10 to decrease the noise shown in the
dark environment.
Drag the slider to adjust the exposure level from 0 ~ 4.
Wide Dynamic Range (WDR) is used when users need to increase image recognizability in
overexposure and dark areas.
The options are: LOW / MIDDLE / HIGH / OFF
Shutter Speed is a function that can adjust the duration of the electronic shutter to produce
optimum image quality. Select the shutter speed suitable for your environment.
Select "ON" to enable the defog function in poor weather conditions such as fog, smog or
smoke. The captured image can be improved.
Select "Auto" to automatically enable IR LEDs at night or in the dark environment, or "OFF" to
disable this function.
Select the level for IR light to activate. 0 ~ 20
Configure from 0 ~ 60 seconds to delay the switch of the IR mode at night, or select "0" to
disable this function.
This is used for the environment where the light condition may change suddenly and usually
last for a short time, for example, the entrance of a parking lot. It may cause the day & night
mode switching constantly and damage the camera.
With this function, the camera will delay the mode switch at night since the light change is
temporary and unnecessary to pay attention.
Click to reset all camera settings to their default values.
Click to reboot the camera if necessary.
CH4