Dell Inspiron 1110 설치 매뉴얼 - 페이지 37

{카테고리_이름} Dell Inspiron 1110에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dell Inspiron 1110 48 페이지. Dell inspiron inspiron 11z: specifications
Dell Inspiron 1110에 대해서도 마찬가지입니다: 제품 안전 데이터 시트 (7 페이지), 특징 (2 페이지)

페이지 인쇄

The following problems may cause print quality deviations, jamming, or even damage to the printer:

Symptom

Poor print quality or toner adhesion, problems

with feeding

Dropout, jamming, curl

Increased gray background shading/printer

wear

Excessive curl problems with feeding

Jamming, damage to printer

Problems with feeding

NOTE:

Do not use letterhead paper printed with low-temperature inks, such as those used in some types of thermography.

NOTE:

Do not use raised or embossed letterhead.

NOTE:

The printer uses heat and pressure to fuse toner to the paper. Insure that any colored paper or preprinted forms use inks that are compatible

with this fusing temperature (200°C or 392°F for 0.1 second).

Paper Specifications

Paper Output Capacity

Output Location

Paper Output Tray (Face Down)

Printer and Paper Storage Environment

Paper storage conditions directly affect the feed operation.

Ideally, the printer and paper storage environment should be at or near room temperature, and not too dry or humid. Remember that paper is hygroscopic: it

absorbs and loses moisture rapidly.

Heat works with humidity to damage paper. Heat causes the moisture in paper to evaporate, while cold causes it to condense on the sheets. Heating

systems and air conditioners remove most of the humidity from a room. As paper is opened and used, it loses moisture, causing streaks and smudging. Humid

weather or water coolers can cause the humidity to increase in a room. As paper is opened and used it absorbs any excess moisture, causing light print and

dropouts. Also, as paper loses and gains moisture it can become distorted. This can cause paper jams.

Care should be taken not to purchase more paper than can be used in a short time (about 3 months). Paper stored for long periods may experience heat and

moisture extremes, which can cause damage. Planning is important to prevent damage to large supplies of paper.

Unopened paper in sealed reams can remain stable for several months before use. Opened packages of paper have more potential for environment damage,

especially if they are not wrapped with a moisture-proof barrier.

The paper storage environment should be properly maintained to ensure optimum performance. The required condition is 20°C to 24°C (68°F to 75°F), with a

relative humidity of 4 percent to 55 percent. The following guidelines should be considered when evaluating the paper's storage environment:

Paper should be stored at or near room temperature.

The air should not be too dry or too humid.

Problem with Paper

Too moist, too rough, too smooth, or embossed;

faulty paper lot

Stored improperly

Too heavy

Too moist, wrong grain direction, or short-grain

construction

Cutouts or perforations

Ragged edges

Specifications

5.5~8.0 pH

0.094~0.18 mm (3.0~7.0 mils)

Flat within 0.02 in (5 mm)

Cut with sharp blades with no visible fray.

Must not scorch, melt, offset, or release hazardous emissions when heated to 200°C (392°F) for 0.1 second.

Long Grain

4%~6% by weight

100~250 Sheffield

Capacity

100 sheets of 75 g/m² bond (20 lb) paper

Solution

Try another kind of paper, between 100-400

Sheffield, 4%~5% moisture content.

Store paper flat in its moisture-proof wrapping.

Use lighter paper; use the rear output slot.

• Use the rear output slot.

• Use long-grain paper.

Do not use paper with cutouts or perforations.

Use good quality paper.