Allied Telesis AT-PB13 빠른 설치 매뉴얼 - 페이지 2
{카테고리_이름} Allied Telesis AT-PB13에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Allied Telesis AT-PB13 2 페이지. Fast ethernet media converters
페이지 인쇄Cable Specifications
The following table lists the cable specifications for the 10Base-T twisted pair
port on all AT-PB10 series modules.
Connector
Type of Twisted Pair Cable
RJ-45
Unshielded/Shielded Twisted Pair Category 3 or
better
The second port on the AT-PB15 has a BNC connector with a maximum
operating distance of 185 meters (606 feet). The following table lists the cable
specifications for the 10Base-F fiber optic port on the AT-PB13 and AT-PB14
when operating in full-duplex mode.
Model
Connector
Type of Fiber Optic Cable
AT-PB13
ST
50/125 µm or 62.5/125 µm multimode
AT-PB14
SC
50/125 µm or 62.5/125 µm multimode
Cable specifications for half-duplex operation can be found in the PowerBlade
Chassis Installation Guide.
Package Contents
Make sure the following items are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales representative for
assistance.
One AT-PB10 Series Media Converter Module
This quick install guide
Warranty card
Installing the Media Converter
1. Remove a blank faceplate from an empty expansion slot on the front of the
chassis. The module can be installed in any expansion slot.
2. Remove the module from the shipping package and store the packaging
material in a safe place. Be sure to observe standard ESD precautions.
3. For an AT-PB15 module, check the setting of the J5 jumper. If the chassis
does not contain an AT-PBM02 management module, set the jumper to the
disabled position. Refer to the PowerBlade Chassis Installation Guide for
the jumper location.
4. Slide the module into the expansion slot, aligning it with the guiderails
until it firmly connects to the chassis' backplane.
2
5. Secure the module to the chassis by tightening the thumbscrew.
6. Verify that the PR LED on the front of the unit is green.
7. Set the LT/ML switch to the ML (MissingLink) position (AT-PB13 or
Maximum
Operating Distance
8. Set the MDI/MDI-X switch for the 10Base-T port to the appropriate
100 m (328 ft)
9. Connect the data cables.
10. The AT-PB10 series module is now ready for use. Repeat this procedure to
Refer to the PowerBlade Chassis Installation Guide for additional
information.
Maximum
Operating Distance
Status LEDs
2 km (1.2 mi)
LED
2 km (1.2 mi)
System LEDs
PR
ML
Port LEDs
LK
RX
Fiber Optic Interface (Multimode)
Receiver
Transmitter
Output Power
AT-PB14 only).
setting.
install additional AT-PB10 series modules.
Color
Description
Green
Power is applied to the media converter.
Green
The MissingLink feature is activated.
OFF
The MissingLink feature is disabled and the unit is
performing a link test.
Green
A link is established on the port.
Green
Data is being received or transmitted by the port.
Typical
Sensitivity
-30 dBm
Saturation
170 µW (-7.6 dBm)
Wavelength
830 nm
Typical
62.5/125 mM
-12 dBm
50/125 mM
-16.5 dBm
Range
N/A
150 µW (-8.2 dBm)
± 20 nm
Worst
-15.0
-19.5 dBm
3