Dell DX6000 개요 - 페이지 11

{카테고리_이름} Dell DX6000에 대한 개요을 온라인으로 검색하거나 PDF를 다운로드하세요. Dell DX6000 19 페이지. Rack installation instructions — static rails
Dell DX6000에 대해서도 마찬가지입니다: 보충 설명서 (4 페이지), 하드웨어 설치 지침 (2 페이지), 사용자 설명서 (46 페이지), 설정 및 구성 매뉴얼 (43 페이지), 설치 및 구성 매뉴얼 (35 페이지), 시작하기 매뉴얼 (28 페이지), 공지 사항 (28 페이지), 공지 사항 (20 페이지), 구성 매뉴얼 (9 페이지), 구성 매뉴얼 (9 페이지), 릴리스 노트 (8 페이지), 참조 매뉴얼 (12 페이지), 구성 매뉴얼 (7 페이지), 릴리스 노트 (6 페이지), 릴리스 노트 (5 페이지), 릴리스 정보 (5 페이지), 설치 지침 (2 페이지), 설치 지침 (2 페이지)

Chapter 2. Installing, Configuring and Running SCSP

Proxy

The SCSP Proxy installs as an RPM and is managed very similarly to other RPM packages. If

the SCSP Proxy is being utilized on a Cluster Services Node (CSN), the installation and base

configuration are performed automatically as part of CSN setup. See the CSN Installation and

Configuration Guide for complete details of customizing the SCSP Proxy on the CSN.

SCSP Proxy has been developed and tested with 64-bit Red Hat Enterprise Linux (RHEL) 5.5.

Other RHEL versions or Linux distributions are not currently supported. The information discussed

in this chapter assumes you use a pre-installed RHEL Linux environment.

To install the SCSP Proxy, you must first install prerequisite packages (if required). The following

topics discuss these tasks in more detail:

•

Section 2.2.1, "Installing SCSP Proxy Prerequisites"

•

Section 2.2.3, "Installing or Upgrading the SCSP Proxy Software"

•

Section 2.2.4, "Configuring the SCSP Proxy"

Before you can install the SCSP Proxy, you must verify the following prerequisites are installed:

• Python 2.5

• Python Setuptools 0.6c9

• Twisted 8.2.0

None of the preceding are available as standard RPM packages with RHEL 5.5; however, a Python

2.5-compatible Twisted RPM is located in the /scspproxy directory of this SDK.

If you are installing the SCSP Proxy on a Cluster Services Node (CSN), all of the required RPMs are

installed for you.

If you are installing the SCSP Proxy on a non-CSN system, you can manually install the packages

using commands like the following (in the order shown):

yum -y --nogpgcheck install caringo-3rdparty-Python-2.5.4-x86_64.rpm

yum -y --nogpgcheck install caringo-3rdparty-setuptools-0.6c9-x86_64.rpm

yum -y --nogpgcheck install caringo-3rdparty-Twisted-8.2.0-x86_64.rpm

Before starting your Proxy installation, upgrade to RHEL 5.5 using upgrade utilities provided with the

operating system.

Installing the SCSP Proxy from the SDK is similar to installing the prerequisites because the

procedure is different depending on whether or not you have CSN. To install the SCSP Proxy from

the SDK, do either of the following:

Version 1.2

December 2010