Allied Telesis Rapier 48i 빠른 설치 매뉴얼 - 페이지 6

{카테고리_이름} Allied Telesis Rapier 48i에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Allied Telesis Rapier 48i 13 페이지. Rapier switch
Allied Telesis Rapier 48i에 대해서도 마찬가지입니다: 데이터시트 (6 페이지), 빠른 설치 매뉴얼 (12 페이지), 빠른 설치 매뉴얼 (11 페이지), 데이터시트 (3 페이지), 데이터시트 (3 페이지), 데이터시트 (2 페이지), 빠른 설치 매뉴얼 (12 페이지)

페이지 인쇄
Allied Telesis Rapier 48i 빠른 설치 매뉴얼
6
Figure 1: Rapier front panel and rear panel with AC power inlet.
Front panel
25
26
Uplink Module Bays
Rear panel
100-240 VAC
RPS Inlet for
Power Inlet
AT-PWR8000
10BASE-T / 100BASE-TX
1X
3X
5X
7X
9X
11X
2X
4X
6X
8X
10X
12X
10/100 BASE Ports
7.
Apply DC power to the switch (for DC models)
Read the Safety and Statutory Information booklet before connecting a DC
power supply. A copy of this booklet is included with each switch. It is also
included on the Documentation and Tools CD-ROM, or can be
downloaded from www.alliedtelesyn.co.nz/support/rapier/.
Only trained and qualified personnel should connect a DC power supply. Due
to exposed terminals, DC powered switches should be installed only in
Restricted Access Areas.
DC supply cable specifications:
•
Number of wires (cores): 3
•
Minimum size: 2.1mm
•
Minimum cable rating: 600V, 90 degrees Celsius
DC power supply specifications:
•
48 VDC (39-60 VDC is acceptable)
•
Either positive grounded or negative grounded
Circuit protection:
•
Use a 10 Amp circuit breaker
To connect the DC supply:
a) Ensure the supply cable is not live
b) Strip the supply cable wires to expose 8mm (0.31 in.) of bare conductor
c) At the switch, connect the ground wire to the ground terminal. These
terminals can be identified by the diagram on the switch's rear panel
(see Figure 2). Tighten the terminal to between 0.6 and 0.8 Nm (0.041 to
0.055 pound-force per foot)
13X
15X
17X
19X
21X
23X
14X
16X
18X
20X
22X
24X
NSM BAY
2
(14 AWG)
Rapier Switch
Layer 3 Fast Ethernet Switch
PORT ACTIVITY
RS-232
TERMINAL PORT
L /A
100M LINK /
ACTIVITY
10M LINK /
ACTIVITY
FULL DUP
HALF DUP/
COL
D/C
1
3
5
7
9
11
13
15
17
19
21
23
ASYN0
L /A
D/C
L /A
D/C
2
4
6
8
10
12
14
16
18
20
22
24
Port LEDs
System
LEDs
RS-232 Terminal Port
NSM 0
Swap
Hot Swap
In Use
NSM Hot Swap
Button and LEDs
C613-04017-01 REV G
STATUS
FAULT
RPS
RESET
PWR