3 Com U.S. Robotics 3469 설치 매뉴얼

{카테고리_이름} 3 Com U.S. Robotics 3469에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3 Com U.S. Robotics 3469 1 페이지. Terminal adapter for windows and macintosh

페이지 인쇄

READ

FIRST!

3 Com U.S. Robotics

ISDN Pro TA

Installation Guide

for Windows

and Macintosh

Deutsche Installationsanleitung auf der

Rückseite.

part number 1.024.2088-01

Before Y

Befor

e Y

e You Begin

e Y

ou Begin

Using the correct cable

You can install this Terminal Adapter (TA) as a serial or USB (if supported) device.

Look at the ports on the back of your computer to determine which cable you

should use.

Use a DB25F/DB25M RS-232

Use the serial cable supplied

serial cable (not supplied)

with your TA

Use a Macintosh mini DIN eight-pin

Use the USB cable supplied with

serial cable (not supplied)

your TA

Installing this TA as a USB device

To use this TA as a USB device, your computer must run Windows 98 with Service

Pack 1 or better, or Macintosh System 8.5. (I-Macs must also have I-Mac Update

1.1.) It must also have an enabled USB port.

If you are using a Macintosh, verify that you are using supported Macintosh system

software by clicking the Apple Menu and selecting About This Computer. If you are

using an I-Mac, verify that you are using supported software by clicking the Apple

Menu and selecting System Profiler. Then click the Devices and Volumes tab.

To verify that you are using Windows 98 Service Pack 1 or better and that your USB

port is enabled:

. Click Windows Start, select Settings, and click Control Panel. Then double-click the

System icon.

2. The "System Properties" screen appears. Your Windows version information is listed

under "System."

3. Click the Device Manager tab. If "Universal serial bus controller" appears in the list

of system devices without a red X or exclamation mark over the icon, then USB is

configured properly.

For information about enabling your USB port, consult the documentation that came

with your computer or operating system.

Prepare for installation.

Shut down your computer.

Copy the serial number from the underside or pack-

aging of your TA into the box below.

TA serial number

When you order ISDN service, you will be provided

with up to three MSNs. Write these numbers in the

boxes below.

ISDN MSNs

Install the ControlCenter

software and supply your

country information.

If you are using an IBM-compatible computer, click

and Run. In the "Open" text box, type D:\setup.exe.

Then click OK. (If your CD-ROM drive uses a different

letter, type that letter instead of "D." ) Follow the onscreen

instructions to install the Connections CD and

ControlCenter.

If you are using a Macintosh, ControlCenter was installed

automatically when you installed your drivers.

NOTE:

You can reinstall ControlCenter from your Connec-

tions CD if necessary.

ControlCenter allows you to configure your ISDN line set-

tings and adjust other settings as needed. When you run

ControlCenter for the first time, the software will detect

your ISDN TA. Click the icon for your ISDN TA to select it.

You will then be asked to select the country you are in and

to set the MSNs for your ISDN line.

You must supply the above information in order to use your

ISDN TA. For further instructions on using ControlCenter,

consult the online help feature of ControlCenter or your

ISDN TA's electronic User Guide on the Connections CD.

Connect the TA to the computer.

you

are

installing

this

as a serial device (Windows or Macintosh):

Connect the 25-pin male end of the serial cable to your ISDN TA and the

other end to your computer's serial port.

NOTE:

If you are using an IBM

-compatible computer, your serial port will

normally be labeled COM, MODEM, RS-232, 10101, or SERIAL. Do not

use AUX, GAME, LPT, PRINTER, or PARALLEL.

If you are using a Macintosh, your serial port will be labeled

you

are

installing

this

as a USB device (Windows or Macintosh):

Your TA was supplied with a USB cable. Connect the six-sided end of this

cable to the TA and the other end to your computer's USB port. If your

computer has more than one USB port, you can use either one.

NOTE:

The USB port will be labeled either "USB" or

USB or Serial

Verify the TA is properly

installed (Windows only).

If you are installing this TA as a

serial or USB device:

When your desktop returns, click

, and click

double-click the Modems icon. This screen should dis-

play a description of the TA. Click the

tab, then click the COM port next to the description of

your TA. Note the name of the COM Port assigned to

your TA in the box below (for instance

COM Port

Click

. Your TA's command set should

appear in the box, confirming that it is functioning prop-

erly. Click

, then click

close "Modem Properties."

Connect the TA to an ISDN phone jack and

any analogue devices to the TA.

Plug one end of the supplied ISDN phone cable into your TA's ISDN jack

(labeled "ISDN"). Plug the other end into your ISDN wall jack.

NOTE:

In many cases, your wall jack will have NT-1 support built in. If it does

not, you will need to plug your ISDN TA into an external NT-1 unit and plug that

unit into your wall jack. For further information on NT-1 support in your area,

contact your ISDN service provider or phone company.

You can also plug analogue devices, such as a conventional telephone,

answering machine, fax machine, or analogue modem, into either one of

the two jacks labeled

on your TA.

Connect the power supply to the TA.

Plug the power supply block into your wall socket. Then plug the power supply cable

with the single round end into the back of your TA.

NOTE:

supplied with your TA.

Install the driver software.

If you are installing this TA as

a Windows serial device:

Windows 95 Version A:

Turn on your computer. When the "New Hardware

Found" screen appears, click

Insert the Connections

CD supplied with your ISDN TA into your CD-ROM

drive and click

. Type D:\ in the box and click

your CD-ROM drive uses a different letter, type that letter instead of "D." )

Windows will find the driver file and copy it to your hard drive.

Windows 95 Version B:

Turn on your computer. When the "Update Device Driver

Wizard" appears, click

. Insert the Connections CD supplied with

your ISDN TA. Windows will find the driver file and copy it to your hard drive.

Then click

Windows 98:

Turn on your computer. When the "Add New Hardware Wizard"

appears, click

. Insert the Connections CD supplied with your ISDN

TA. Click Search for the best driver for your device and click

CD-ROM drive and click

. When Windows finds the driver file, click

to copy it to your hard drive. Then click

Windows NT 4.0:

Turn on your computer. Once you have logged in, click Win-

dows Start, select Settings, and click Control Panel. Then double-click the Mo-

dems icon.

If you have other modems or ISDN devices installed on your computer, the

"Modems Properties" screen appears. Click the Add button. When the "Install

New Modems" screen appears, click

modems or ISDN devices installed on your computer, the "Install New Mo-

dems" screen appears. When it does, click

Windows will detect your ISDN TA but will refer to it as a "Standard Modem."

Click

. Insert the Connections CD supplied with your ISDN TA. Click

Have Disk . Select 3 Com U.S. Robotics ISDN Pro TA EXT. Then click

Click

. Fill out the information requested on the "Location Informa-

tion" screen. Click

. Then click

, select

If you are installing this TA

. Then

as a Windows 98 USB device:

Turn on your computer. When the "Add New Hardware Wizard" appears, click

. Insert the Connections CD supplied with your ISDN TA. Then click

Search for the best driver for your device and click

Specify a location is selected and click

) .

button. Double-click your CD-ROM drive's icon. Click the USB folder and

. Click

and

Wizard" appears. When it does, repeat the steps to finish installing your ISDN

TA.

If you are installing this TA

on a Macintosh (USB or serial):

Turn on your computer and insert the Connections CD. Then double-click your

CD-ROM drive's icon or the Connections icon. Follow the onscreen instructions

to install the Connections CD. The appropriate drivers for your ISDN TA will be

installed automatically.

Use only the power supply

. (If

. Select

. If you do not have other

. Make sure

. Then click the Browse

. The "Add New Hardware