Dell PowerVault NX1950 설정

{카테고리_이름} Dell PowerVault NX1950에 대한 설정을 온라인으로 검색하거나 PDF를 다운로드하세요. Dell PowerVault NX1950 2 페이지. For vmware esx server software
Dell PowerVault NX1950에 대해서도 마찬가지입니다: 배포 매뉴얼 (34 페이지), 중요 정보 매뉴얼 (26 페이지), 시작하기 (49 페이지), 설치 및 문제 해결 매뉴얼 (48 페이지), 배포 매뉴얼 (38 페이지), 업그레이드 매뉴얼 (18 페이지), 참조 매뉴얼 (4 페이지), 사용 (2 페이지), 구성 매뉴얼 (11 페이지)

페이지 인쇄

N157DA00.qxd

1/11/2008

3:59 PM

Page 1

Setting Up Your Dell

™

PowerVault

Before You Begin

CAUTION:

Before you set up and operate your Dell PowerVault system, read and follow the safety instructions in your

Product Information Guide .

1. Identify the Solution

A -- Integrated Solution

B -- Dell|EMC Gateway Solution

C -- Dell|EqualLogic Gateway Solution

This page contains steps 1 and 2 of the quick setup. Steps 3 and 4 are

overleaf.

2. Unpack Your System

Unpack the system and save all accessories, documentation, and media.

3. Install the System in a Rack

This system requires a properly grounded electrical outlet, a compatible rack,

and a rack installation kit.

NOTE: For information on compatibility of drivers and firmware, see the Dell PowerVault NX1950

Systems Support Matrix .

PCI-E (option 1-SAS Controller, option 2-Fibre

Broadcom

BCM5708C TOE NIC2 connector

Channel Controller, option 3-NIC)

Broadcom BCM5708C TOE NIC1 connector

power supply 1

USB connectors (2)

power supply 2

10.

video connector

system status indicator

11.

serial connector

system identification button

12.

remote access controller port

system status indicator connector

NOTE: The default user name is administrator and the default password is storageserver .

NOTE: It is recommended that you configure iSCSI traffic and the public Ethernet traffic on separate

networks.

™

NX1950 Storage Solution

Integrated Solution MD3000 (Solution A)

Cabling the Integrated Solution – Highly-Available

1-A

(Two-Node Cluster) Configuration

PowerVault NX1950 storage system 0

PowerVault NX1950 storage system 1

controller 0

controller 1

PowerVault MD3000 storage array

NOTE: For single node configuration, the cabling for the PowerVault NX1950 storage system 1 does

not apply.

NOTE: The default password for your PowerVault NX1950 storage solution is storageserver .

NIC port A to Gb Ethernet switch for cluster (optional)

NIC port B to Gb Ethernet switch (optional)

Gb1 and Gb2 to Gb Ethernet swith(es)

Port 1 on PowerVault NX1950 storage system 0 SAS HBA to In-0 on controller 1

Port 1 on PowerVault NX1950 storage system 1 SAS HBA to In-1 on controller 1

Port 0 on PowerVault NX1950 storage system 1 SAS HBA to In-1 on controller 0

Port 0 on PowerVault NX1950 storage system 0 SAS HBA to In-0 on controller 0

DRAC port to Ethernet switch for lights-out management (optional)

Connection to PowerVault MD1000 expansion enclosure (optional)

2-A

Power-Up Procedure

1 Turn on the PowerVault MD1000 expansion enclosure(s). The expansion status

LED must display steady blue.

2 Turn on the PowerVault MD3000 storage array. The status LED indicates that the

unit is ready. The following list indicates several states of the storage array:

If the status LED displays a solid amber light, the PowerVault MD3000

storage array is initializing.

If the status LED displays blinking amber, there is an error in initialization. You

can view the error in PowerVault Modular Disk Storage Manager.

If the status LED displays a solid blue light, the PowerVault MD3000 storage

array is completely initialized.

3 Turn on the PowerVault NX1950 storage system.

NOTE: If you turn on the PowerVault NX1950 storage system before the PowerVault MD3000 storage

array has initialized, the storage system is not recognized by the PowerVault NX1950 storage

solution.

Configuring IP Address Network Settings on a PowerVault NX1950 Storage

System

You can configure IP address network settings on the PowerVault NX1950 storage

system using one of the following methods:

Special Administration Console

Direct connection using keyboard, video, and mouse

NOTE: It is recommended that you use a static IP address for network connection.

Gateway Solution Dell|EMC (Solution B)

1-B

Cabling the Gateway Solution Dell|EMC

PowerVault NX1950 storage system

NOTE: The default password for your PowerVault NX1950 storage solution is storageserver .

NOTE: This illustration depicts the default configuration of the Dell|EMC Gateway solution.

The actual configuration of solution you have purchased may vary.

NIC port A to Gb Ethernet switch (optional)

Port 1 on HBA to SAN.

NIC port B to Gb Ethernet switch (optional)

DRAC port to Ethernet switch for lights-out

Gb1 and Gb2 to Gb Ethernet swith(es)

management (optional)

Port 2 on HBA to SAN.

2-B

Power-Up Procedure

1 Ensure that the Dell|EMC storage array is turned on.

2 Turn on the PowerVault NX1950 storage system.

NOTE: If you turn on the PowerVault NX1950 storage system before the Dell|EMC storage array

has initialized, the storage system is not recognized by the PowerVault NX1950 storage solution.

Configuring IP Address

Network settings on PowerVault NX1950 storage system can be configured

using the following methods:

Special Administration Console

Direct connection using keyboard, video, and mouse

NOTE: It is recommended that you use a static IP address for network settings.

Configure Dell|EMC Storage Array Zoning

Zoning determines the mapping from PowerVault NX1950 storage systems to

the storage arrays. Configure zoning to the Dell|EMC storage arrays on your

SAN switches. For more information, see your switch documentation.

Enter EMC PowerPath License Key

Enter the EMC PowerPath license key when prompted. The license key is

required only for EMC CX-series storage arrays.

NOTE: The PowerPath key is optional and only required to enable load balancing.

Install EMC Navisphere Agent

The EMC Navisphere Agent installer is launched automatically the first time

you log into the server. Privileged Users list should be left empty after

installation because the D D e e l l l l S S t t o o r r a a g g e e I I n n i i t t i i a a l l i i z z a a t t i i o o n n W W i i z z a a r r d d populates it.

Gateway Solution Dell|Equallogic (Solution C)

1-C

Cabling the Gateway Dell|Equallogic Solution

PowerVault NX1950 storage system

NOTE: The default password for your PowerVault NX1950 storage solution is storageserver .

NOTE: This illustration depicts the default configuration of the Dell|Equallogic Gateway

solution. The actual configuration of the solution you have purchased may vary.

Quad-port Gigabit NICs connected to iSCSI SAN or

Dual-port Gigabit NICs connected to iSCSI SAN or

public Ethernet network

Quad-port Gigabit NICs connected to iSCSI SAN or

DRAC port to Ethernet switch for lights-out

public Ethernet network

management (optional)

NOTE: Networking Requirement-During configuration—You must configure the server and the

storage array on the same network. Do not block the layer-2 Multicasting between the server

and the storage array.

2-C

Power-Up Procedure

1 Ensure that the Dell|Equallogic storage array is turned on.

2 Turn on the PowerVault NX1950 storage system.

NOTE: Turn on the PowerVault NX1950 storage system only after the Dell|Equallogic storage

array has initialized to ensure that the storage system is recognized by the PowerVault NX1950

storage solution.

Configuring IP Address

Use one of the following methods to configure network settings on the

PowerVault NX1950 storage system:

Special Administration Console

Direct connection using keyboard, video, and mouse

NOTE: It is recommended that you use a static IP address for the network settings.

Configure Networking on Dell|Equallogic Storage Array

Configure your network for the Dell|Equallogic storage arrays on your Ethernet

switches. For more information, see your switch documentation.

Initialize Dell|Equallogic storage Array if not Initialized Already

The Equallogic remote installer is launched automatically the first time you log

into the server. Initialize your array if not already initialized.