Dell PowerEdge M420 릴리스 정보 - 페이지 13

{카테고리_이름} Dell PowerEdge M420에 대한 릴리스 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Dell PowerEdge M420 27 페이지. Dell poweredge blade servers getting started guide
Dell PowerEdge M420에 대해서도 마찬가지입니다: 정보 업데이트 (38 페이지), 매뉴얼 (25 페이지), 사용자 설명서 (23 페이지), 중요 정보 매뉴얼 (35 페이지), 업데이트 매뉴얼 (32 페이지), 업데이트 매뉴얼 (28 페이지), 사용자 설명서 (26 페이지), 사용자 설명서 (22 페이지), 시작하기 매뉴얼 (12 페이지), 매뉴얼 (38 페이지), 기술 매뉴얼 (46 페이지), 기술 매뉴얼 (48 페이지), 포트폴리오 매뉴얼 (27 페이지), 시작하기 매뉴얼 (14 페이지), 시작하기 매뉴얼 (12 페이지)

페이지 인쇄

PowerConnect M6220/M6348/8024/8024F/M8024/M8024-k/

7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes

 LACP Ports Inactive Until Attached

Ports in a LAG configured to use LACP (dynamic LAG) remain inactive (discard received traffic) until they become

attached to the LAG. LACP ports that are attached to a LAG will enter the discarding state if they become detached

from the LAG for any reason.

Port level configuration for a port that is configured in a dynamic LAG is disregarded. Remove the port from the LAG

to restore use of the port level configuration.

Ports in a static LAG begin forwarding on link up. Ports in a static LAG disregard port level configuration. Configure

static LAG functions on the static LAG interface.

NOTE:

It is recommended that administrators disable portfast and auto-

portfast on physical interfaces configured in a LAG. Portfast and auto-

portfast can interfere with an interface entering into LAG mode on a

reboot and possibly enable a packet storm.

 Spanning Tree Changes

Administrators may assign more than 1024 VLANs to MSTP instances. Only VLANs that are configured on the switch

will forward traffic.

The PowerConnect switches implements the 802.1Q-2005 standard which builds on 802.1D-2004. 802.1D-2004

incorporates the the 802.1t, 802.1w and 802.1s revisions. Port path costs are calculated based on the interface speed as

shown below and are dynamically recalculated on interface activation and link speed changes.

External Port Path Cost values (Port Path Cost in 17.14 of 802.1D-2004) are applicable in STP, RSTP, and MST modes

(Ref. Table 17-3 802.1D-2004). Use the spanning-tree cost command in interface mode to set the external port path

cost.

Link Speed

10 Gb/s

1 Gb/s

100 Mb/s

10 Mb/s

1 Mb/s

Internal Port Path Cost values are specific to MST mode only (Ref. Table 13-3 802.1Q-2005). Use the spanning-tree

mst <instance> cost command in interface mode to set the internal port path cost.

Link Speed

10 Gb/s

1 Gb/s

100 Mb/s

10 Mb/s

1 Mb/s

System Firmware Version 4.1.0.6

Default Value

2000

20000

200000

2000000

20000000