EarthWay EV-N-Spred C22HDS 조립 및 작동 지침 매뉴얼 - 페이지 5
{카테고리_이름} EarthWay EV-N-Spred C22HDS에 대한 조립 및 작동 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. EarthWay EV-N-Spred C22HDS 6 페이지. Broadcast spreader
EarthWay EV-N-Spred C22HDS에 대해서도 마찬가지입니다: 조립 및 작동 지침 매뉴얼 (8 페이지), 조립 및 작동 지침 매뉴얼 (6 페이지)
페이지 인쇄
16. For normal operation both doors should be fully opened. To reduce flow to the left side, partially or completely close the door over the
rear (LARGE) hole. To reduce flow to the right side, partially or completely close the door over the front (SMALL) hole. Close both doors
for a narrow center spread pattern.
WARNING: If the optional side deflector is being used in the down position, the plate over the rear (LARGE) hole MUST BE CLOSED or
an over application of
material will occur.
Full Rate Path
Finish
Start
The settings furnished on the Setting Matrix are intended as a guide only. Variations in physical characteristics of material applied, walking
speed, and roughness of ground surface may require slightly different spreader settings. Due to these conditions, EarthWay makes no
warranty as to the uniformity of coverage actually obtained from the settings listed.
EarthWay Products, Inc. warrants this product free of defects in original workmanship and materials for a period of 5-Years to the end
user with the original purchase receipt. If a manufacturing non-conformance is found, EarthWay Products, Inc. at its discretion will
repair or replace the part(s) or product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse,
tampering, or normal wear and tear as determined by EarthWay . EarthWay at its discretion may require that the part(s) or product be
returned along with the original purchase receipt at owners' expense for examination and compliance with the terms of this warranty. (Do
not return any product without first receiving authorization from EarthWay Products, Inc.). To seek remedy under this warranty, contact
EarthWay Products, Inc. at 574-848-7491, [email protected] or write to ( EarthWay Products, Inc. P.O. Box 547 Bristol,
Indiana 46507) and describe the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s)
or product; any labor charges associated with repair or replacement of non-conformances are specifically excluded. Due to the corrosive
nature of most fertilizers and ice melt products, EarthWay Products, Inc. makes no warranty against and specifically excludes part(s) or
product degradation or failure due to corrosion or its effects, or the use of powdered materials. Clean and dry your spreader thoroughly
after each use, as a preventative measure, coat all metal parts with a light oil or silicon spray.
Before filling hopper, become familiar with the operation of this spreader.
5 Obtain proper setting for material to be used from the enclosed SETTING MATRIX included with this spreader, or from our web site
under the MANUALS SECTION.
5 Move stop bolt on rate gauge assembly to the proper setting.
5 While pushing spreader forward, pull control lever back to stop bolt.
5 To stop, push lever forward to close flow holes before you stop moving.
5 When finished, empty any remaining material from hopper.
5 Thoroughly wash spreader and allow to dry before storing. A coating of light oil will help prevent corrosion.
5 If you must use Rock Salt, Remove agitator when using Rock Salt to prevent damage to the gearbox.
You now can Register your product online at
www.earthway.com/support.
Please keep the original purchase receipt because it
will be needed if you need warranty coverage.
Half Rate Path
Finish
Start
5-YEAR LIMITED WARRANTY
OPERATING INSTRUCTIONS
Constant Spread Width
Infinitely Variable
Throwing Port Openings
HOW TO ORDER SPARE PARTS
All spare parts listed may be ordered direct from
EarthWay Products, Inc.
Be sure to give the following information when ordering.
Model Number
Part Number
Part Description
Call (574) 848-7491, 800-294-0671,
or email: [email protected] for current prices.
Both ports open
Both ports closed
One port closed
PAGE 5