EarthWay 6500 HIGH-WHEEL 조립 지침

{카테고리_이름} EarthWay 6500 HIGH-WHEEL에 대한 조립 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. EarthWay 6500 HIGH-WHEEL 2 페이지.

6500 HIGH-WHEEL CULTIVATOR

ASSEMBLY INSTRUCTIONS

Congratulations on the purchase of this new Earthway High-Wheel Cultivator. Please contact us if you have any difficulty

with assembly or operation of this product. We can be reached via the telephone at 800-294-0671 or 574-848-7491 Monday -

Friday 9:00am ~ 4:00pm or visit us online at www.earthway.com The 6500 comes with lifetime technical support, email us at

[email protected].

HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY

The 6500 will require approximately 30 minutes to assemble with common hand tools.

5 Remove and identify all loose parts from carton

5 Clean and dry your Cultivator thoroughly after each use.

5 Coat all metal surfaces with a light oil to prevent corrosion

ASSEMBLY STEPS

I. Assemble both (4) Upper and (3) Lower Handles together and secure with (12) 5/16-18 x 1½" hex bolt & (15) 5/16" hex nut - do not

tighten.

II. Assemble (7) Left and (6) Right Tool Supports, by positioning (9) Tool Support Spacer between them at the end that has only one

hole as shown in the exploded view, secure using (11) 5/16-18 x 1¼" hex bolt and (15) hex nut and tighten. Make sure that you have

the Right and Left in the correct position as shown in the exploded view.

III. Connect (2) Frame to the Tool Support Assembly from step 2 using (14) 1/4-20 x 2" hex bolt thru the (2) Frame and then through

both (6 & 7) Tool Supports, then through (2) Frame on the other side and secure with (16) 1/4-20 lock nut, and tighten.

IV. Install (8) Cross Brace on to the Upper Handle and secure with (10) 1/4-20 x 1½" hex bolt and (16) 1/4-20 lock nut to each side,

loosely tighten.

V. Install (5) Axle into (24) Wheel and position between the (2) Frame rails.

VI. Now insert (13) 5/16-18 x 4½" hex bolt through the hole in (3) Lower Handle, (2) Frame, then into (5) Axle & (24) Wheel, then (2)

Frame, (3) Lower Handle and secure with (17) Lock Washer & (15) 5/16-18 hex nut, and tighten.

VII. Now determine a comfortable operation height and then remove (15) 5/16-18 hex nut and select one of the four adjustment holes in

the top of (6 & 7) Tool Supports and secure with (15) 5/16-18 hex nut and tighten.

VIII. Go back and tighten all hardware.

(2) 31100

(3) 31111

(2) 31115

1/4-20 x

5/16-18 x 1"

5/16-18 x 1½"

1½" Bolt

Bolt

#10

#11

#12

(1) 43033

(1) 34104

Formed

5/16" Lock

Washer

#18

#15

(1) 36302

(6) 32102

3/8"-16

5/16"-18

Hex Nut

ASSEMBLY OF TOOLS

FURROW PLOW

Place Furrow Plow in front of tool support slot. Put carriage bolt (19) through square hole and through slot in tool support. Next put formed

washer (21) over carriage bolt (18) and tool support: fasten with lock nut (18) and tighten fully.

HILLING / MOLD BOARD PLOW

Place Hilling Plow in position shown above. Put carriage bolt (19) through square hole and through slot in tool support. Next put formed

washer (21) over carriage bolt (18) and tool support: fasten with lock nut (18) and tighten fully.

FIVE TINE

Assemble Fine Tine as pictured above. Fasten with two bolts(11) and two (15) hex nuts, tighten fully. Next put carriage bolt (19) through rear

of the Five Tine Assembly and through tool support, fasten with formed washer (21) and lock nut (18).

(1) 31120

(1) 37105

(1) 31116

1/4-20 x 2"

3/8-16 x 2"

5/16-18 x 4½"

Bolt

Carriage Bolt

Bolt

#14

#19

#13

#16

(3) 32103

(1) 23605

1/4"-20

Tool Support

Lock Nut

Spacer

(see above right)

(1) 23500

Axle

Furrow Plow

#44227

Hilling/Mold Board

Plow #44228

Earth Way

Five Tine

Cultivator

#60141

Slicing Hoe #60132

5-2014 Pt. 52126