HP 2530p - EliteBook - Core 2 Duo 2.13 GHz 설정 및 구성 매뉴얼 - 페이지 11

{카테고리_이름} HP 2530p - EliteBook - Core 2 Duo 2.13 GHz에 대한 설정 및 구성 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HP 2530p - EliteBook - Core 2 Duo 2.13 GHz 18 페이지. Notebook pc
HP 2530p - EliteBook - Core 2 Duo 2.13 GHz에 대해서도 마찬가지입니다: 사양 (36 페이지), 제품 설명서 (16 페이지), 사용자 설명서 (15 페이지), 네트워크 매뉴얼 (16 페이지), 사양 (2 페이지), 사용자 설명서 (27 페이지), 설정 매뉴얼 (19 페이지), 개요 (16 페이지), 매뉴얼 (12 페이지), 소프트웨어 설치 매뉴얼 (8 페이지), 매뉴얼 (6 페이지), 드라이버 설치 (20 페이지), 매뉴얼 (20 페이지), 매뉴얼 (7 페이지), 사용자 설명서 (31 페이지), 사용자 설명서 (46 페이지), 사용자 설명서 (44 페이지), 사용자 설명서 (42 페이지), 사양 (45 페이지), 사용자 설명서 (30 페이지), 사용자 설명서 (24 페이지), 빠른 사양 (46 페이지)

페이지 인쇄
HP 2530p - EliteBook - Core 2 Duo 2.13 GHz 설정 및 구성 매뉴얼

Enterprise Mode Setup and Configuration

Enterprise mode is for large corporate customers. In this mode, a Setup and Configuration Server
(S&CS) is required. An S&CS is a server that runs an application over a network that performs AMT
Setup and Configuration.
The S&CS is also known as a Provisioning Server as seen in the MEBx. The act of setting up and
configuring the AMT is also known as "provisioning".
An S&CS is typically provided by ISVs and is contained within the ISV management console product.
Customers should consult with their management console supplier for more information.
Enterprise Mode – AMT Setup and Configuration Steps:
The ME Setup portion for Enterprise mode is the same as SMB mode. Repeat Steps 1 through 12 to
perform ME Setup. This will take the system from Factory mode to In-Setup Mode.
The following are quick steps for ME Setup.
1) Get into the MEBx by pressing Ctrl-P during POST.
2) Enter the default password "admin".
3) Change the MEBx password, follow strong password guidelines.
4) Go into Intel ME Configuration.
5) Check the Intel ME State Control, select Enabled.
6) Skip the Intel ME Firmware Local Update Qualifier.
7) Skip LAN Controller.
8) Go into Intel ME Features Control
a. Check Manageability Features Selection, select Intel AMT.
9) Go into Intel ME Power Control. (for AMT 2.x only)
a. Go into ME State upon Initial Power-On, select mobile: ON in S0, S3/AC, S4-5/AC.
10) Exit and save.
11) Look for Intel ME Configuration Complete message.
12) System will reboot.
Once the system reboots, starting with Step 13, some of the options will be set differently than SMB
mode.
(for AMT 2.x only)
13) Enter the MEBx password.
14) Go into the Intel AMT Configuration.
The Intel AMT Configuration screen has more options than could be displayed in one page.
More options are available if the menu is scrolled down.
15) Go into Host Name.
a. Enter a host name
Default Setting
Recommended Setting
Spaces are not accepted in the host name.
16) Go into TCP/IP.
b. Disabling Network Interface
Default Setting
(The LAN controller option is not available for AMT 4.x)
(for AMT 2.x only)
(for AMT 2.x only)
: None
: User Dependent
: Network Interface Enabled
(for AMT 2.x only)
11