HP 8530w - EliteBook Mobile Workstation 네트워크 매뉴얼 - 페이지 12

{카테고리_이름} HP 8530w - EliteBook Mobile Workstation에 대한 네트워크 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HP 8530w - EliteBook Mobile Workstation 16 페이지. Hp elitebook mobile workstation
HP 8530w - EliteBook Mobile Workstation에 대해서도 마찬가지입니다: 브로셔 및 사양 (8 페이지), 빠른 사양 (36 페이지), 사용자 설명서 (15 페이지), 브로셔 및 사양 (4 페이지), 사양 (4 페이지), 액세서리 매뉴얼 (2 페이지), 브로셔 및 사양 (6 페이지), 사용자 설명서 (27 페이지), 설정 매뉴얼 (19 페이지), 개요 (16 페이지), 매뉴얼 (12 페이지), 소프트웨어 설치 매뉴얼 (8 페이지), 매뉴얼 (6 페이지), 설정 및 구성 매뉴얼 (18 페이지), 매뉴얼 (20 페이지), 매뉴얼 (7 페이지), 사용자 설명서 (28 페이지), 빠른 사양 (47 페이지)

페이지 인쇄
HP 8530w - EliteBook Mobile Workstation 네트워크 매뉴얼

Solving travel connection problems

If you experience modem connection problems when using the computer outside of the country in which
you purchased it, try the following suggestions.
●
Check the telephone line type.
The modem requires an analog, not a digital, telephone line. A line described as a PBX line is
usually a digital line. A telephone line described as a data line, fax machine line, modem line, or
standard telephone line is usually an analog line.
●
Check for pulse or tone dialing.
An analog telephone line supports one of 2 dialing modes: pulse dialing or tone dialing. These
dialing mode options are selected in the Phone and Modem Options settings. The dialing mode
option selected must match the dialing mode supported by the telephone line in your location.
To determine the dialing mode supported by a telephone line, dial a few digits on the telephone,
and then listen for clicks (pulses) or tones. Clicks indicate that the telephone line supports pulse
dialing. Tones indicate that the telephone line supports tone dialing.
To change the dialing mode in your current modem location setting, follow these steps:
1.
Select Start > Control Panel > Network and Internet Connections.
2.
In the left side panel, click Phone and Modem Options.
3.
Then click the Dialing Rules tab.
4.
Select your modem location setting.
5.
Click Edit.
6.
Click either Tone or Pulse.
7.
Click OK twice.
●
Check the telephone number you are dialing and the response of the remote modem.
Dial a telephone number, make sure there is a response from the remote modem, and then hang
up.
●
Set the modem to ignore dial tones.
If the modem receives a dial tone it does not recognize, it does not dial and displays a "No Dial
Tone" error message.
To set the modem to ignore all dial tones before dialing, follow these steps:
1.
Select Start > Control Panel > Network and Internet Connections.
2.
In the left side panel, click Phone and Modem Options.
3.
Then click the Modems tab.
4.
Click the listing for the modem.
5.
Click Properties.
6.
Click Modem.
6
Chapter 1 Using the modem (select models only)
ENWW