allpa 487190 지침 책자 - 페이지 5

{카테고리_이름} allpa 487190에 대한 지침 책자을 온라인으로 검색하거나 PDF를 다운로드하세요. allpa 487190 10 페이지. Vitroceramic cookjng hob

페이지 인쇄

Turning Touch Control on/off

After start-up, the touch control requires about one second before it is ready for use. After reset, all displays and

LED s will flash for about 1 second. After this time, all displays and LED s go off and the touch control is in

stand-by status. The touch control can be turned on using the power supply button (key ON/OFF).

The displays of the cooking zones will show. If a cooking zone is hot, the display will show H . The touch control is

turned on exclusively by using only the power supply button alone. Pressing the power supply button at the same

time as other keys has no effect and the touch control remains in standby status. The touch control can be

switched off at any time using the power supply button. This is also the case if the control has been locked

with the child safety feature. The power supply button always has highest priority for shutdown.

Turning on a cooking zone

With the touch control on, select a cooking zone pressing the selection key. The respective display show a "0", the

plate is ready. If the area is hot an H will be shown on the display for the corresponding plate. By pressing the

key "+" you can select a power level and the zone will start heating up. Starting from level 1, it is increased by one

every 0.4sec. Upon reaching level 9 you cannot make any further increases. If the cooking zone is selected

using the "-" key, the initial level is 9 (the highest level available). If you hold down the key, the active level

decreases. When you reach 1 you cannot decrease it any further. Use the "+" or "-" keys for change settings.

Turning off the cooking zones

Select the zone you want to turn off using the selection key. The selection is shown by a dot in the display of the

relative zone. If you press the keys "+" and "-" at the same time, the power level will be set to 0. As an alternative,

the key "-" can be used to decrease the power level down to 0. If all cooking zones are at power level 0 , the

decimal points in the display will flash. If a cooking zone is hot, an H will be shown rather than a 0 .

All cooking zones can be switched off immediately, at any moment, by pressing the power button.

Automatic heating function (where supplied)

When the automatic heating function has been activated, the power of the cooking zone reaches 100% for an

established heating time, which depends on the selected power level. At the end of this heating time, the touch

control returns to the pre-selected power level. Procedure to start automatic heating:

- The control unit is switched on and a cooking zone is selected;

- After setting cooking stage "9" automatic heating is activated by pressing the "+" key again.

Immediately afterwards, a "A" appears on the display.

Once the parboiling boost has ended, only the selected cooking stage is indicated on the display.

Using the "minus" key you can de-activate the function at any time.

Automatic switch off function (limitation of operating time)

Based on the power level, each cooking zone is shut off after a maximum preset time if no operations are

performed. Each operation with the cooking zone (using the PLUS or MINUS keys, or the dual circuit in the

zone where present) resets the maximum operation time to its initial value.

When the control is on, the ON/OFF key has priority over all other keys, so that the control

can be shut off at any time, even in the event of multiple or continuous activation of keys.

In standby mode, continuous activation of keys will not have any effect. However, before the

electronic control can be turned back on, it must recognize that no key is activated.

Child-Lock function (where supplied)

Where present the "key-lock" button, press it for lock. Press again it to un-lock.

Otherwise, to lock press the cooking zone select key and the minus key simultaneously followed by pressing the

cooking zone select key again. All displays show an L for LOCKED (= child lock against unintentional activation).

This operational procedure must take place within 10sec and no other key than the one described above may be

pressed. The electronics remains in a locked condition until its released, even if the control until is switched off

and on again in the meantime. For release, press the cooking zone select and the minus key simultaneously.

L for LOCKED disappears from the display and all cooking zones display 0 with a flashing dot. After switching

off the control unit the child lock is reactivated. For de-active the lock function definitely, press the cooking zone

select key and the minus key simultaneously followed by pressing only the minus key again. After carrying out all

steps in the correct order and within a period of 10 sec, the locking is cancelled and the control unit is in a

STAND-BY mode. If the control unit is switched on again by pressing the ON/OFF key, all displays show "0",

the display dots keep flashing and the control unit may be operated for cooking.