Dialogic 64-0014-02 빠른 설치

{카테고리_이름} Dialogic 64-0014-02에 대한 빠른 설치을 온라인으로 검색하거나 PDF를 다운로드하세요. Dialogic 64-0014-02 2 페이지. Media board

페이지 인쇄

Dialogic

D/120JCT-LS

Media Board

Part Number

64-0014-02

Dialogic Corporation.

1. Protecting the Board from Damage

CAUTION

! All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-

sensitive boards and components at a static-safe work

area, and observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions,

visit

http://www.dialogic.com/support/hwinstall

learn more.

Unpacking the Board

Unpack the Dialogic

D/120JCT-LS board ("board")

according to the following steps:

1. Prepare a static-safeguarded work area.

2. Carefully remove the board from the shipping

carton and anti-static packaging. Handle the

board by the edges and avoid touching the

board's components.

3. Lay the board on the static-dissipative work

surface.

Note: Place boards in static-shielding bags when

carrying boards from station to station.

CAUTION: Do not remove the board from the anti-

static packaging until you are ready to install it.

Observe proper anti-static precautions at all times.

2. Installation Order

Dialogic recommends that you install Dialogic

hardware before Dialogic

software. However, if you

are adding hardware to an existing system, you do not

need to uninstall existing Dialogic software.

3. Set the Hardware Switches

Dialogic

boards use Plug and Play technology,

including hardware auto-configuration for IRQ and

memory address. These boards allow you to use the

factory default hardware settings for quick installation

and operation. However, Dialogic recommends that

you review the following information and select

options as desired.

IMPORTANT: More than one PCI board may be set

to ID 0. For more information, contact Dialogic

Support at

http:/www.dialogic.com/support/helpweb/.

Connecting the CT Bus Cable

Use the CT Bus cable to connect the Dialogic

D/120JCT-LS board with the other boards in the

system.

Plug the CT Bus Cable into

the CT Bus Connector

Plug the CT Bus cable into the CT Bus connector. To

connect to the SCbus, use the CT Bus to SCbus

adapter (Part Number 882-757-xx) and follow the

instructions included with the adapter.

Install the CT Bus/SCbus Adapter

Align pin 1 of the adapter with pin 1 of the edge

connector on the board. NOTE: Edge connector is

not labeled.

Press the CT Bus/SCbus Adapter to the board.

Connect the CT Bus and SCbus cables as per the

installation instructions for your Dialogic

Board Numbering

When you start Dialogic

boards, each board is

assigned a sequential number for identification and

use by the application program. The board number is

based on the board ID that is set through hardware

switches on the board (rotary switch SW100).

Set the board ID switches to select the board

sequencing method as follows:

Geographical Sequence (by PCI Bus and

Slot Number) Board ID 0 (factory default)

All Dialogic

PCI boards can share the factory default

setting of board ID 0. Board numbers will be assigned

in ascending order based on the PCI bus and slot

number.

If you add a board to the system, it could change the

Dialogic

board numbering, depending upon the PCI

bus and slot number where you install it. Also, PCI

boards that use ID 0 for the geographical numbering

sequence will be numbered before boards that use

board IDs 1-9, A-F. The geographical method is not

available for ISA bus boards.

Programmable Sequence

(by Dialogic

Board ID): Board IDs 1-9, A-F

In addition to the geographical assignment method, the

programmable assignment method can be used to

further identify the boards in your system.

If you change the board ID from the factory default of

0 to any other number, the software will use that

setting to identify the board.

Important! When not set to 0, the board ID must

be unique (it must not conflict with the board ID of

any other Dialogic

ISA or PCI board which has

been manually assigned). If you use this method,

Dialogic recommends that you assign sequential

numbers starting at 1. This method is also used for

all ISA bus boards.

Precedence in Mixed Systems

In systems using both methods, or where both ISA and

SW100

Baseboard

board(s).

PCI Bus Connector

Rear Bracket

PCI boards exist, PCI boards will take precedence and

will be numbered before an ISA bus board that uses

board IDs 1-9, A-F.

Set the Hook-Switch State for Start-Up

Set the SW1 slide switch as follows to select how the

board responds to an incoming call when the PC

power is on, but the board is not initialized.

Off-Hook

On-Hook

Each RJ-14 jack on the rear bracket of the voice board

supports two channels. A standard telephone will not

function when directly attached to the board.

Note: The RJ-14 jacks use 2 tip/ring pairs with 2

earth recalls,

one for each

channel.

RJ-14

Pinouts

Physical Description

SW1

CT Bus Connector

Slot Retainer Bracket

(Optional)

SW1 ON

SW1 OFF

Connect External Cabes

REAR BRACKET

6 Earth Recall 2

5 Ring 2

4 Tip 1

Channel 1

3 Ring 1

2 Tip 2

1 Earth Recall 1

6 Earth Recall 2

5 Ring 2

4 Tip 1

Channel 2

3 Ring 1

2 Tip 2

1 Earth Recall 1

6 Earth Recall 2

5 Ring 2

4 Tip 1

Channel 3

3 Ring 1

2 Tip 2

1 Earth Recall 1

6 Earth Recall 2

5 Ring 2

4 Tip 1

Channel 4

3 Ring 1

2 Tip 2

1 Earth Recall 1

6 Earth Recall 2

5 Ring 2

4 Tip 1

Channel 5

3 Ring 1

2 Tip 2

1 Earth Recall 1

6 Earth Recall 2

5 Ring 2

4 Tip 1

Channel 6

3 Ring 1

2 Tip 2

1 Earth Recall 1

Part

Function

SW100

Rotary switch used to

determine board ID

Slide switch for on/off

SW1

hook on power up

RJ-14 connectors

J1-J6