Dialogic Dialogic D/480JCT-2T1-EW 설치 매뉴얼 - 페이지 2

{카테고리_이름} Dialogic Dialogic D/480JCT-2T1-EW에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dialogic Dialogic D/480JCT-2T1-EW 2 페이지. Eicon networks dialogic installation guide

페이지 인쇄

WARNING! Installing the Dialogic

D/480JCT-2T1-EW board in a x1 slot with the

P3 jumper in position 1-2 will void the

warranty of the D/480JCT-2T1-EW board.

If the Dialogic

D/480JCT-2T1-EW will be

connected to other telephony boards via a CT Bus

cable, you should install the boards to minimize

unused connectors on the CT Bus cable (in addition

to ensuring that the power requirements are met):

Install boards in adjacent slots whenever

■

possible.

If the Dialogic

D/480JCT-2T1-EW board will be

■

connected to one or more PCI boards, use the

PCI Express slot(s) closest to the PCI slots.

5. Installing the Board

WARNING! Unplug the equipment before

performing the procedures described here.

Failure to disconnect the power before you

open the chassis can result in personal injury.

Ensure that the system is disconnected from

its power source and from all

telecommunications links, networks, or

modem lines whenever the chassis cover is

removed. Do not operate the system with the

cover removed.

CAUTION: To avoid possible damage to the board,

remove power from the computer before beginning

installation. Observe proper anti-static precautions

at all times while handling and installing the board.

To install the Dialogic

D/480JCT-2T1-EW board,

perform the following steps:

1. Turn off all power to the system and disconnect

the system's power cords.

2. Remove the computer's cover.

3. Choose an empty PCI Express expansion slot

and remove the slot's retaining screw and

access cover plate.

4. Insert the board's edge connector into the bus

slot, and apply firm pressure to the top edge of

the board until the board is fully seated in the

edge connector.

Remove

Cover

PCI Express

Plate

Board

Computer

Chassis

PCI Express

Slots

PCI Slots

5. Reinstall the retaining screw.

6. Repeat steps 1 through 5 for any additional

boards you are installing.

7. Connect the telephony boards together with a

CT Bus cable of the appropriate size (not

included). If possible, use a cable assembly that

matches the number of boards in your system.

If the cable has more than one unused

connector, install the cable so that all the

unused connectors are at one end of the cable.

CT Bus

Colored

Cable

Stripe

(Pin 1)

Note:

Your CT Bus cable may

have a different number of

connectors (drops).

8. Replace the computer's cover.

9. Reconnect the computer's power cord.

6. Connecting to External

Equipment

Each RJ-48C jack on the rear bracket of the

Dialogic

D/480JCT-2T1-EW board supports a

single T1 digital network interface. Use appropriate

cables to connect the RJ-48C jacks on the bracket

to your CSU or other network termination

equipment. The bottom RJ-48C connector is for

span 1, the top connector is for span 2.

The following figure illustrates the pinout of the

RJ-48C jacks.

Pinout for RJ–48C Jacks

Network Interface

on PCI Express Bracket

Cable Connector

RCV_RING

Pin 1

RCV_TIP

Chassis Ground

XMIT_RING

XMIT_TIP

Chassis Ground

7. After Installing the Board

If you are installing the Dialogic

D/480JCT-2T1-EW in a system that already has the

Dialogic system software installed, you may not

need to install a new or upgraded software release

to support the board. The Dialogic

D/480JCT-2T1-EW has been designed to be

compatible with existing System Release 6.x

software versions that support PCI boards. Please

refer to the Release Update document for your

release version for up-to-date information about

support for PCI Express boards and any known

issues relating to their use.

If this is the first Dialogic

telecom board you have

installed in your system, you will need to install an

appropriate version of the Dialogic

System

Software and configure the software for the specific

board(s) you are using. Refer to the installation

and configuration documentation that accompanies

the release for instructions.

When configuring the system for the Dialogic

D/480JCT-2T1-EW board, use the same menu

selections and configuration settings that are

documented for the PCI version of the

D/480JCT-2T1 board.

8. Removing the Board

Removal of the Dialogic

D/480JCT-2T1-EW board

is essentially the reverse of the installation

procedure:

1. Observe anti-static precautions.

2. Disconnect the telephony cables.

3. Remove the computer's power cord.

4. Remove the computer's cover.

5. Disconnect the CT Bus cable (if applicable).

6. Remove and set aside the board's retaining

screw.

7. Remove the board and place it static-protective

packaging.

9. Contacting Technical Support

Dialogic provides technical support for its products

through a network of value added distributors who

are trained to answer technical questions on

installing and configuring Dialogic® products. If

you are unsure how to contact your support

channel, please call Dialogic in the United States at

973-967-6600 (9am - 5pm EST) and we will assist

in obtaining the appropriate support channel.

Outside the United States please refer to

http://www.dialogic.com/support/contact to obtain

local contact information.

Dialogic also provides direct support via Dialogic®

Pro™ Services agreements. For more details of

direct support from Dialogic please refer to

http://www.dialogic.com/support/DialogicPro.

10.Returning a Product

To return a board for warranty repair or any other

returns, please refer to the following:

http://www.dialogic.com/support/hwfaults

Reserved. You may not reproduce this document in whole or in

part without permission in writing from Dialogic Corporation at

the address provided below.

All contents of this document are subject to change without

notice and do not represent a commitment on the part of

Dialogic Corporation or its subsidiaries. Reasonable effort is

made to ensure the accuracy of the information contained in

the document. However, due to ongoing product improvements

and revisions, Dialogic Corporation and its subsidiaries do not

warrant the accuracy of this information and cannot accept

responsibility for errors or omissions that may be contained in

this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN

CONNECTION WITH DIALOGIC® PRODUCTS. NO LICENSE,

EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY

INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT. EXCEPT AS EXPLICITLY SET FORTH BELOW OR AS

PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND

DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER,

AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED

WARRANTY, RELATING TO SALE AND/OR USE OF DIALOGIC

PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING

TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY,

OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT

OF A THIRD PARTY. Dialogic products are not intended for use

in medical, life saving, life sustaining, critical control or safety

systems, or in nuclear facility applications. It is possible that

the use or implementation of any one of the concepts,

applications, or ideas described in this document, in marketing

collateral produced by or on web pages maintained by Dialogic

Corporation or its subsidiaries may infringe one or more

patents or other intellectual property rights owned by third

parties. Dialogic Corporation or its subsidiaries do not provide

any intellectual property licenses with the sale of Dialogic

products other than a license to use such product in accordance

with intellectual property owned or validly licensed by Dialogic

Corporation or its subsidiaries. More detailed information about

such intellectual property is available from Dialogic

Corporation's legal department at 9800 Cavendish Blvd., 5th

Floor, Montreal, Quebec, Canada H4M 2V9. The software

referred to in this document is provided under a Software

License Agreement. Refer to the Software License Agreement

for complete details governing the use of the software.

Dialogic Corporation encourages all users of its products to

procure all necessary intellectual property licenses required to

implement any concepts or applications and does not condone

or encourage any intellectual property infringement and

disclaims any responsibility related thereto. These intellectual

property licenses may differ from country to country and it is

the responsibility of those who develop the concepts or

applications to be aware of and comply with different national

license requirements.

Dialogic, Dialogic Pro, Brooktrout,

Cantata, SnowShore, Eicon, Eicon Networks, Eiconcard, Diva,

SIPcontrol, Diva ISDN, TruFax, Realblocs, Realcomm 100,

NetAccess, Instant ISDN, TRXStream, Exnet, Exnet Connect,

EXS, ExchangePlus VSE, Switchkit, N20, Powering The

Service-Ready Network, Vantage, Connecting People to

Information, Connecting to Growth, Making Innovation Thrive,

and Shiva, among others as well as related logos, are either

registered trademarks or trademarks of Dialogic. The names of

actual companies and products mentioned herein are the

trademarks of their respective owners.