Miller 028042103 소유자 매뉴얼 - 페이지 6

{카테고리_이름} Miller 028042103에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Miller 028042103 20 페이지.
Miller 028042103에 대해서도 마찬가지입니다: 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (20 페이지)

페이지 인쇄

READ INSTRUCTIONS.

D Read and follow all labels and the Owner's

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each

section.

D Use only genuine replacement parts from the manufacturer.

D Perform installation, maintenance, and service according to the

Owner's Manuals, industry standards, and national, state, and

local codes.

D Read and understand the Safety Data Sheets (SDSs) and the

manufacturer's instructions for adhesives, coatings, cleaners,

consumables, coolants, degreasers, fluxes, and metals.

STEAM AND HOT COOLANT can burn.

Hose may rupture if coolant overheats.

D Visually inspect condition of hoses before each

use. Do not use damaged hoses.

Allow cooling period before working on equipment.

1-4. California Proposition 65 Warnings

WARNING: This product can expose you to chemicals in-

cluding lead, which are known to the state of California to

cause cancer and birth defects or other reproductive

harm.

For more information, go to www.P65Warnings.ca.gov.

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, American Welding

Society standard ANSI Standard Z49.1. Website: www.aws.org.

Safe Practices for the Preparation of Containers and Piping for Welding

and Cutting, American Welding Society Standard AWS F4.1 from Glob-

al Engineering Documents. Website: www.global.ihs.com.

Safe Practices for Welding and Cutting Containers that have Held Com-

bustibles, American Welding Society Standard AWS A6.0 from Global

Engineering Documents. Website: www.global.ihs.com.

National Electrical Code, NFPA Standard 70 from National Fire Protection

Association. Website: www.nfpa.org and www. sparky.org.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1

from Compressed Gas Association. Website:www.cganet.com.

Safety in Welding, Cutting, and Allied Processes, CSA Standard

W117.2 from Canadian Standards Association.

Website: www.csagroup.org.

OM-254203 Page 2

HIGH PRESSURE FLUIDS can injure or kill.

D Coolant can be under high pressure.

D Release pressure before working on cooler.

D If ANY fluid is injected into the skin or body seek medical help

immediately.

MOVING PARTS can injure.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards

closed and securely in place.

D Have only qualified persons remove doors, panels, covers, or

guards for maintenance and troubleshooting as necessary.

D Reinstall doors, panels, covers, or guards when maintenance is

finished and before reconnecting input power.

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1 from American National Standards Institute.

Website: www.ansi.org.

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B from National Fire Protection Association.

Website: www.nfpa.org.

OSHA Occupational Safety and Health Standards for General Industry,

Title 29, Code of Federal Regulations (CFR), Part 1910.177 Subpart N, Part

1910 Subpart Q, and Part 1926, Subpart J. Website: www.osha.gov.

OSHA Important Note Regarding the ACGIH TLV, Policy Statement on

the Uses of TLVs and BEIs. Website: www.osha.gov.

Applications Manual for the Revised NIOSH Lifting Equation from the

National Institute for Occupational Safety and Health (NIOSH). Web-

site: www.cdc.gov/NIOSH.