Miller Digital Performance Series 매뉴얼 - 페이지 6

{카테고리_이름} Miller Digital Performance Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Miller Digital Performance Series 32 페이지. Auto-darkening helmets
Miller Digital Performance Series에 대해서도 마찬가지입니다: 매뉴얼 (28 페이지), 소유자 매뉴얼 (32 페이지)

페이지 인쇄
Miller Digital Performance Series 매뉴얼
Specification
Viewing
Field
Operating
Two Modes: Weld, Grind
Modes
Reaction
Time
Available
Shades
All Shades
Provide
Continuous UV
And IR Protec-
tion.
Sensitivity
Control
Adjustable For
Varying Ambi-
ent Light And
Welding/Cut-
ting Arc.
No. 10 Setting
Locks Lens In
Dark State.
Delay
Control
Slows Lens
Dark-To-Light
State.
Automatic
Power
Low Battery
Light
Power
Supply
OM-256 476 Page 4
SECTION 2 − SPECIFICATIONS
Digital
Pro-Hobby Helmet
3.75 x 1.55 in.
(95 x 40 mm)
0.0000500 sec
(1/20,000)
Weld Mode
Darkened State:
No. 8 − No. 13
Light State:
No. 3
Grind Mode
Light State: No. 3
Weld Mode:
No. 0 − No.10
Grind Mode:
Not Applicable
Weld Mode:
No. 0 − No. 10
Grind Mode:
Not Applicable
Shuts Lens Off 45 Minutes After Last Arc Is Struck.
Lens automatically turns on when arc is struck.
Red LED Illuminates To Indicate 2−3 Days Remaining Battery Life.
CR2450 Lithium Batteries (Miller Part No. 217 043)
Digital
Performance Helmet
3.81 x 1.85 in.
(97 x 47 mm)
Three Modes: Weld,
Cut, Grind
0.0000500 sec
(1/20,000)
Weld Mode
Darkened State:
No. 8 − No. 13
Light State: No. 3
Cut Mode
Darkened State:
No. 5 − No. 8
Light State: No. 3
Grind Mode
Light State: No. 3
Weld Mode:
No. 0 − No. 10
Cut Mode:
No. 0 − No. 10
Grind Mode:
Not Applicable
Weld Mode:
No. 0 − No. 10
Cut Mode:
No. 0 − No. 10
Grind Mode:
Not Applicable
Digital Elite
Helmet
3.81 x 2.62 in.
(97 x 60mm)
Four Modes: Weld, Cut,
Grind, X-Mode
0.0000500 sec
(1/20,000)
Weld Mode
Darkened State:
No. 8 − No. 13
Light State: No. 3
Cut Mode
Darkened State:
No. 5 − No. 8
Light State: No. 3
Grind Mode
Light State: No. 3
X-Mode
Darkened State:
No. 8 − No. 13
Light State: No. 3
Weld Mode:
No. 0 − No. 10
Cut Mode:
No. 0 − No. 10
Grind Mode:
Not Applicable
X-Mode:
No. 0 − No. 10
Weld Mode:
No. 0 − No. 10
Cut Mode:
No. 0 − No. 10
Grind Mode:
Not Applicable
X-Mode
No. 0 − No. 10