AQUARAY AQUABEAM 설치 및 사용 설명서 지침 - 페이지 5

{카테고리_이름} AQUARAY AQUABEAM에 대한 설치 및 사용 설명서 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. AQUARAY AQUABEAM 6 페이지. Solid state lighting systems

페이지 인쇄

M INTEN NCE

Caution: To avoid possible electric shock, special care should be taken when

using this electrical appliance near water.

Caution: Always isolate the PSU from mains electricity before installing or

carrying out any maintenance to the AquaRay lamp unit.

Caution: Do not attempt to open the plastic case of the PSU. This will invalidate the

1 year guarantee on the PSU.

Caution: Do not attempt to open the plastic casing of your AquaRay lamp unit.

This will damage the waterproof sealing and invalidate the 5 year guarantee on

the lamp unit.

An AquaRay lamp unit and associated power supply unit (PSU) are sealed units

and are not customer serviceable parts. The lamp array inside the lamp unit is

also not a customer serviceable part and the whole lamp unit is to be disposed of

at the end of its life (>50,000 hours).

An AquaRay lamp unit should need little or no maintenance once set up. However

due to salt deposits and the high calcium level in marine aquariums it is common

for deposits to build up on the body of the unit.

Therefore it is recommended that:-

a. The lens face of the AquaRay lamp unit is cleaned periodically with a warm,

damp cloth.

b. The heat sink on the rear of the unit is kept free of large particles of salt

and other films or deposits which might obstruct the free movement of air

around the vanes of the heat sink. Occasional cleaning with a small brush

and/or dry, lint-free cloth is recommended.

TROUBLE SHOOTING

Problem: The quaRay lamp unit does not switch on.

Solution: Check cable connection between lamp unit and PSU.

Solution: Check power cord is firmly connected to PSU.

Solution: Check (and replace if necessary) the fuse in the power cord plug (UK only).

If the lamp unit is still not switching on, return the PSU and lamp unit to your

local stockist for further testing and replacement if necessary.

Problem: The quaRay lamp unit starts flashing.

Solution: Return the PSU to your local stockist for replacement with an authentic

Tropical Marine Centre part.

Problem: One or more lamps in the quaRay lamp unit do not come on

or cease to work.

Solution: Return lamp unit to your local stockist for replacement with an authentic

Tropical Marine Centre part.

Problem: The quaRay lamp unit has been accidentally immersed.

Solution: Immediately switch off the mains supply to the PSU and remove the

lamp unit from the water while holding the unit vertically with the cable entry

end uppermost.

Disconnect the AquaRay lamp unit from the PSU via the connector located

150mm/6" from the PSU. If immersed it is normal for some water to be held

around the outside edge of the AquaRay lamp unit and this can be removed by

gently shaking the unit vertically and then drying carefully with a lint-free cloth.

When fully dry, check to see if any water or drips are visible inside the main

body of the unit when observed through the front lens cover. Holding the unit

vertically with the cable entry end uppermost will ensure that any water will

move to the opposite end of the unit, where it may be more easily observed

and will do the least damage should the unit need to be returned to Tropical

Marine Centre for repair. If you are in any doubt as to whether water has

penetrated the unit then do not reconnect to the PSU and immediately return

the unit to your local stockist for further inspection by Tropical Marine Centre.

Please Note:

installation of the lamp unit will invalidate the guarantee on the lamp

unit.

For further information, please see our

" quaRay F Qs" section on our website:

www.tropicalmarinecentre.co.uk

ccidental immersion or partial/fully submerged