AquaScape 180 GPH 설치 지침

{카테고리_이름} AquaScape 180 GPH에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. AquaScape 180 GPH 2 페이지. Table top fountain, spitter and statuary submersible pump
AquaScape 180 GPH에 대해서도 마찬가지입니다: 지침 및 유지보수 매뉴얼 (2 페이지)

페이지 인쇄

I N S T A L L A T I O N

STATUARY WATER PUMP

70 GPH Water Pump

180 GPH Water Pump

Item #91023

Item #91025

90 GPH Water Pump

320 GPH Water Pump

Item #91024

Item #91026

Contents

No.

Description

No.

1/4" Stepped Plastic Adapter

1/2" Cylinder Plastic Adapter

5/8" Straight Adapter Tube

5/8" Bent Adapter Tube

70 GPH

180 GPH

Safety Information

WARNING: Risk of electric shock – This pump has not been approved for use in

swimming pool or marine areas

WARNING: To provide continued protection against risk of electric shock, connect to

properly grounded, ground fault circuit interrupter (GFCI) outlets only, using the following

guidelines:

(A) Have a qualified electrician install a properly grounded receptacle outlet, acceptable for outdoor

use and protected from snow and rain.

(B) Inspect cord before using.

(D) Any wiring of pumps should be performed by a qualified electrician to ensure code compliance

and user safety.

(E) Unplug pump at receptacle outlet when not in use or before removal from pond.

(F) To reduce risk of electrical shock, all wiring and junction connections should be made per local

codes. Requirements may vary depending on usage and location.

(G) The power cable should be protected at all times to avoid punctures, cuts, bruises and

abrasions.

(H) Never handle power cords with wet hands.

(I) Do not remove cord and strain relief. Do not connect conduit to pump.

(J) Do not use power cable to lift pump.

• Always operate the pump fully submerged; or if using in-line ensure a constant source of fresh

water. Failure to do so may overheat the pump and cause it to fail, voiding the warranty.

• Use only in fully assembled state, paying particular attention to ensure that both the outer and inner

filter screens are attached to the pump. Failure to operate the pump without the filter screen will

allow large debris to enter the pump and cause the pump to fail, voiding the warranty.

• Do not wear loose clothing that may become entangled in the impeller or other moving parts.

• Keep clear of suction and discharge openings. DO NOT insert fingers into pump with power

connected.

• Do not pump hazardous materials or liquids, such as oil, saltwater or organic solvents.

• Do not block or restrict discharge.

• Products returned must be cleaned, sanitized, or decontaminated, as necessary, prior to shipment

to ensure that employees will not be exposed to health hazards in handling said material. All

applicable laws and regulations shall apply.

IMPORTANT: Aquascape, Inc. is not responsible for losses, injury, or death resulting from

a failure to observe these safety precautions, misuse or abuse of pumps or equipment.

Description

Flow Controller

Impeller

Impeller Cover

Intake Screen

90 GPH

320 GPH

facebook.com/aquascapeinc

youtube.com/aquascape4

pinterest.com/aquascapeinc

instagram.com/aquascape_inc

I N S T R U C T I O N S

Statuary Water Pump Specifications

• Input Voltage: 120V AC

• Input Frequency: 60 Hz

• Submersible pump

• For outdoor or indoor use

Model

Max Flow Rate GPH/LPH

Max Head Height

Motor Type

Wattage

Amperage

Power Cord Length

Discharge Hose Diameter

Installation

This pump is designed to be operated fully submerged in the

water feature (Ex. 1).

1. Select the appropriate fitting(s) needed for your

application.

2. Attach tubing to the fitting (Ex. 2).

3. Connect the other end of the tubing to the fountain,

ornamental spitter, or filter.

• Connect the pump to an outlet that is protected by a ground

fault interrupter (Ex. 3). Once the pump is running and water

circulating through the filter(s) or waterfalls, check for any

fitting or waterfall leaks

where the external

connections are made.

General Maintenance

• Inlet Screen Cleaning

– If you notice diminished water flow, check inlet screen and

clean as needed (Ex. 4). Disconnect pump, remove from

water and clean debris from pump cover.

• Internal Pump Cleaning

– If you still have diminished flow rates, remove the impeller

cover to inspect the impeller rotor assembly (Ex. 5).

– If your rotor assembly impeller and internal pump body

have excessive scale build-up, clean with a mild acid, such

as white vinegar or non-abrasive calcium, lime, and rust

remover product

using a sponge or

soft-bristled brush

that won't scratch

impeller (Ex. 6).

Removing scale build

up will allow your

pump to run like new

again.

• Replacing the Impeller

Assembly

– The impeller assembly

is the only moving

part on the pump and will experience wear and tear. If you've cleaned the pump, as described

above, and still experience poor pump performance, it is most likely time to replace the impeller.

Replacing the impeller is extremely easy. Replacement Impeller Kits are available through your

local Aquascape dealer.

Winter Application

• The pump can be run during freezing weather, if desired, but should be removed if shutting down

the pump for the winter. Disconnect the tubing from the discharge fitting and remove the pump

from the pond. Clean the pump and inlet screens with fresh water and store the pump in a frost-

free location.

Troubleshooting

• Reduced Water Flow

– Pump or plumbing may be clogged. It may be necessary to clean the pump intake screen and

impeller.

• Pump Hums and Doesn't Push Water

– Pump or plumbing may be clogged. It may be necessary to clean the pump intake screen and

impeller.

– Remove the intake screen and impeller cover and inspect and clean the impeller rotor assembly

and internal pump body.

– Make sure nothing is blocking or wrapped around the impeller.

– Make sure the pump is receiving the correct voltage.

• Pump Not Working

– The ground-fault circuit-interrupter (GFCI) may have tripped.

– The pump is not receiving the correct voltage.

For more information about our company or products, please visit our website at

aquascapeinc.com or call us at US (866) 877-6637 CAN (866) 766-3426

• Thermally protected

• This pump has been evaluated for use with

freshwater only

• Input amps and wattage - see chart below

Statuary Water Pump Specs

70 GPH

90 GPH

180 GPH

70/250

90/300

180/650

Mag-drive

3.0

4.3

9.3

0.037

0.061

0.175

1/2", 5/8"

Ex. 2

Ex. 5

320 GPH

320/1,200

5.5'

17.6

0.339

Ex. 1

Ex. 3

Ex. 4

Ex. 6

12/14/22