Panasonic WV-SW396 설치 매뉴얼 - 페이지 23

{카테고리_이름} Panasonic WV-SW396에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic WV-SW396 40 페이지. Ip video cameras
Panasonic WV-SW396에 대해서도 마찬가지입니다: 사양 (2 페이지), 설치 매뉴얼 (40 페이지), 양이온 (2 페이지), 통합 참고 사항 (8 페이지)

페이지 인쇄

• 24 V AC power supply connector kit (accessory)

Recommended specification of cable (wire)

Wire size

#24

(AWG),

(0.22 mm)

(0.33 mm)

stranded

wire

Length of

20 m

cable

{65.62 feet}

{98.43 feet}

Terminals of the power supply connector

Pin No.

Signal

24 V AC LIVE

24 V AC NEUTRAL

Ground

Not use

• How to assemble the power supply connector

Remove approx. 3 mm {1/8 inches} of the outer jacket of

the cable and twist the cable core to prevent the short cir-

cuit first.

Insert the tip of the cable into the point A of the contact,

and hold the cable using the cable clamp.

Approx. 3 mm {1/8 inches}

Upper

side

Contact

Insert

Procure either of the following tools for clamping.

Molex manual clamp tool:

57027-5000 (for UL1015), 57026-5000 (for UL1007)

After clamping the contact and the cable, insert the con-

tact properly into the power supply connector housing.

Upper side

Power supply connector housing (accessory)

Important:

• Conduct the electric conduit work after processing

the power supply connector and making sure that the

camera is operating normally.

#22

#20

#18

(0.52 mm)

(0.83 mm)

30 m

45 m

75 m

{147.64 feet}

{246.06 feet}

Cable

Contact

• Network cable

Connect a LAN cable (category 5e or better, STP*) to the

network connector.

* E model only

Important:

• Use all 4 pairs (8 pins) of the LAN cable.

• The maximum cable length is 100 m {328 feet}.

• Make sure that the PoE+ device in use is compliant

with IEEE802.3at standard.

• When connecting both of the 24 V AC power supply

and the PoE+ device for power supply, 24 V AC will

be used for power supply.

Depending on PoE+ (or PoE) devices, the power sup-

ply indicator may light or the network functions may

be unavailable.

In this case, disable the PoE+ (or PoE) settings. Refer

to the operating instructions of the PoE+ (or PoE)

device in use.

• Output cable for the monitor used for adjustment

Connect a coaxial cable (BNC) (only for checking if images

are displayed on the monitor).

This output is provided only for checking the adjustment

of the angular field of view on the video monitor when

installing the camera or when servicing.

Important:

• The monitor out connector for adjustment is provided

only for checking the adjustment of the angular field

of view on the video monitor when installing the cam-

era or when servicing. It is not provided for recording/

monitoring use.

• Black bands may appear at the top and bottom or

right and left of the screen. (That does not affect the

adjustment because the angular field of view is not

changed.)

• External I/O cable

Important:

• Input and output of the external I/O terminal 2 and 3

can be switched by configuring the setting. The

default of EXT I/O terminal 2 is "ALARM IN 2" and of

EXT I/O terminal 3 is "ALARM IN 3". It is possible to

determine whether or not to receive input from EXT

I/O terminal 2 and 3 (ALARM IN2, 3) by selecting

"Off", "Alarm input", "Alarm output" or "AUX output"

for "Terminal alarm 2" or "Terminal alarm 3" on the

[Alarm] tab on the "Alarm" page. Refer to the

Operating Instructions (included in the CD-ROM) for

further information.

• When using the EXT I/O terminals as the output termi-

nals, ensure they do not cause signal collision with

external signals.