Panasonic CT-27HL15UN 서비스 매뉴얼 - 페이지 2
{카테고리_이름} Panasonic CT-27HL15UN에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic CT-27HL15UN 32 페이지.
1 Safety precautions
General guidelines
An isolation transformer should always be used during the servicing of a receiver whose chassis is not isolated from AC power line.
Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical
shocks. It will also protect the receiver from being damaged by accidental shorting that may occur during servicing.
When servicing, observe the original lead dress, especially in the high voltage circuit. Replace all damaged parts (also parts that show
signs of overheating.)
Always replace protective devices, such as fish paper, isolation resistors and capacitors, and shields after servicing the receiver. Use
only manufacturer's recommended rating for fuses, circuits breakers, etc.
High potentials are present when this receiver is operating. Operation of the receiver without the rear cover introduces danger for
electrical shock. Servicing should not be performed by anyone who is not thoroughly familiar with the necessary precautions when
servicing high voltage equipment.
Extreme care should be practiced when handling the picture tube. Rough handling may cause it to implode due to atmospheric
pressure. (14.7 lbs per sq. in.). Do not nick or scratch the glass or subject it to any undue pressure. When handling, use safety goggles
and heavy gloves for protection. Discharge the picture tube by shorting the anode to chassis ground (not to the cabinet or to other
mounting hardware). When discharging connect cold ground (i.e. dag ground lead) to the anode with a well insulated wire or use a
grounding probe.Avoid prolonged exposure at close range to unshielded areas of the picture tube to prevent exposure to x ray
radiation.
The test picture tube used for servicing the chassis at the bench should incorporate safety glass and magnetic shielding. The safety
glass provide shielding for the tube viewing area against x ray radiation as well as implosion. The magnetic shield limits the x ray
radiation around the bell of the picture tube in addition to the restricting magnetic effects. When using a picture tube test jig for service,
ensure that the jig is capable of handling 50kV without causing x ray radiation.
Before returning a serviced receiver to the owner, the service technician must thoroughly test the unit to ensure that is completely safe
to operate. Do not use a line isolation transformer when testing.
Leakage current cold check
Unplug the A.C. cord and connect a jumper between the two plug prongs.Measure the resistance between the jumpered AC plug and
expose metallic parts such as screwheads, antenna terminals, control shafts, etc. If the exposed metallic part has a return path to the
chassis, the reading should be between 240k
reading should be infinite.
Leakage current hot check
Plug the AC cord directly into the AC outlet. Do not use an isolation transformer during the check.
Connect a 1.5k
10 watt resistor in parallel with a 0.15µF capacitor between an exposed metallic part and ground. Use earth ground,
for example a water pipe.
Using a DVM with a 1000 ohms/volt sensitivity or higher, measure the AC potential across the resistor.
Repeat the procedure and measure the voltage present with all other exposed metallic parts.
Verify that any potential does not exceed 0.75 volt RMS. A leakage current tester (such a Simpson model 229, Sencore model PR57
or equivalent) may be used in the above procedure, in which case any current measure must not exceed 0.5 milliamp. If any
measurement is out of the specified limits, there is a possibility of a shock hazard and the receiver must be repaired and rechecked
before it is returned to the customer.
Insulation test
Connect an insulation tester between an exposed metallic part and A.C. line. Apply 2500VAC/60Hz for 1 second. Confirm that the
current measurement is lower than 4.0mA. Repeat test with other metallic exposed parts.
X ray radiation
http://tsn.pstc.panasonic.com/viewing/NA/CT-27HL15N/SIMP/MTNC050426A1/doc/MTN...
and 5.2M . If the exposed metallic part does not have a return path to the chassis, the
Hot check circuit
Page 2 of 32
7/7/2008