Panasonic AW-HE130WP 설치 지침 매뉴얼 - 페이지 5

{카테고리_이름} Panasonic AW-HE130WP에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic AW-HE130WP 24 페이지. Hd integrated camera

Panasonic AW-HE130WP 설치 지침 매뉴얼
Installation precautions (continued)
Before installation, always disconnect the power
„
plug
When installing, always use the supplied components.
Do not disassemble or modify the wall mount adaptor.
Tightening up the mounting screws
„
• Tighten up the screws and bolts securely to the degree that is
appropriate for each of the materials used in the mounting location
and structures.
• After tightening up the screws and bolts, check that there is no
unsteadiness and that the parts have been tightened securely.
• Use the specified tools and tighten the screws firmly.
• Tighten up the screws using the specified torque driver. Do not
use electrical drivers or impact drivers.
When the unit is no longer going to be used, do
„
not leave it lying around, but be absolutely sure
to dispose of it properly.
For details on how to remove the unit, refer to "Removing the
camera" (→ page 13).
When installing, transferring or disposing of
„
the unit, be absolutely sure to hold it by its
pedestal area.
Problems may result if the camera head is held or rotated.
Do not attach a filter, hood, extender or other
„
parts to the unit.
Use the dedicated AC adaptor and power cable
„
provided with the unit.
Connect the AC adaptor and power cable to the power inlet
securely.
Installing the AC adaptor
„
• Do not place the adaptor directly onto a ceiling panel or other such
surface.
Extreme danger is posed when water has collected on the surface
as a result of leaking rain, for instance.
Secure the adaptor firmly to the bottom or other surface of a
reinforcing member made of channel steel where dust and other
foreign matter will not accumulate.
(→ page 11)
• Secure the adaptor firmly so that there will be no chance that it will
fall off or fall down.
Secure it using a strength which can withstand the mass (approx.
0.3 kg (0.66 lb)) of the AC adaptor.
Install the accessory AC adaptor near the main
„
power outlet, and position it in such a way
that its power plug can be plugged into and
unplugged from the outlet easily.
When connecting the AC adaptor to a power outlet on the ceiling or
on any other surface where dust may collect, wipe off the dust on
the power plug at periodic intervals as an anti-tracking measure.
Power switch
„
This unit does not have a power switch. The power turns on when
its power plug is connected to a power outlet. When the power
is turned on, the pan, tilt, zoom and focusing operations are
performed.
1
Before proceeding with maintenance, be absolutely
*
sure to disconnect the power plug from the power outlet.
*
1
The unit is set to Standby mode under factory default settings.
When turning the unit for the first time, release the unit from
Standby mode.
For details, refer to the Operating Instructions.

Connecting the power cable

„
Be absolutely sure to connect the power cable of the AC adaptor
through a circuit breaker using one of the following methods.
(1) C onnect the power cable through a power control unit.
(2) C onnect the power cable to a circuit breaker in a power
distribution panel with a contact distance of 3.0 mm (1/8
inches) or more.
Use a circuit breaker which is capable of shutting off all the
poles of the main power supply with the exception of the
protective ground conductor.
(3) I nstall the AC adaptor near the power outlet, and connect it
through the power plug.
Grounding
„
Before operating the unit, check that SIGNAL GND has been
securely grounded.
If there is a possibility of noise interference
„
Either wire the cables so that the power cable (ceiling light cord) of
AC 100 V
(AC 220 V
  ) or more, and the signal cable are placed
1
2
*
*
at least 1 meter (3.3 ft) apart.
Alternatively run each cable through its own metal conduit.
(The metal conduits must be grounded.)
*
1
For AW-HE130WP, AW-HE130KP
*
2
For AW-HE130WE, AW-HE130KE
Radio signal interference
„
If the unit is positioned near a TV or radio transmitting antenna or a
strong electrical field or magnetic field (such as that generated by a
motor, transformer or power lines), its images may be distorted and/
or the images may be affected by noise.
When connecting the cables, ensure that the
„
connector areas will not be subject to any load.
Doing so may cause malfunctioning.
Allowing the generated heat to escape
„
This unit allows the heat generated inside to escape from its
surfaces.
Do not install the unit in a location where it will be surrounded by
walls or other surfaces and where heat will be trapped.
In addition, the heat is dissipated to the bottom panel which will
warm up over time: This is normal and not indicative of any trouble.
PoE+ power supplies
„
Use a PoE+ (IEEE802.at) compatible hub or power supply device.
5