HP 316095-B21 - StorageWorks Edge Switch 2/24 릴리스 노트 - 페이지 10

{카테고리_이름} HP 316095-B21 - StorageWorks Edge Switch 2/24에 대한 릴리스 노트을 온라인으로 검색하거나 PDF를 다운로드하세요. HP 316095-B21 - StorageWorks Edge Switch 2/24 23 페이지. Edge switch release notes
HP 316095-B21 - StorageWorks Edge Switch 2/24에 대해서도 마찬가지입니다: 업데이트 매뉴얼 (9 페이지), 매뉴얼 (41 페이지), 매뉴얼 (40 페이지), 릴리스 노트 (32 페이지), 릴리스 노트 (27 페이지), 매뉴얼 (26 페이지), 릴리스 노트 (27 페이지), 릴리스 노트 (25 페이지), 설치 지침 매뉴얼 (24 페이지), 릴리스 노트 (23 페이지), 릴리스 노트 (22 페이지), 릴리스 노트 (23 페이지), 릴리스 노트 (19 페이지), 릴리스 노트 (19 페이지), 릴리스 노트 (18 페이지), 사용 설명서 (17 페이지), 릴리스 노트 (17 페이지), 업그레이드 지침 (16 페이지), 사용 설명서 (16 페이지), 설치 지침 매뉴얼 (16 페이지), 릴리스 노트 (16 페이지), 릴리스 노트 (17 페이지), 릴리스 노트 (17 페이지), 릴리스 노트 (11 페이지)

About this document

Before upgrading firmware, it is highly recommended that you back up the

director or edge switch configuration. Refer to your HP StorageWorks Edge

Switch Element Manager User Guide for more information. Embedded Web

Server (EWS) also provides an option to print or save product configuration to a

file. Refer to the HP StorageWorks Embedded Web Server User Guide for more

information.

All products must be running firmware 05.00.00 or later before upgrading to

06.02.00-22. If a switch is operating with a firmware level earlier than 05.00.00,

you must upgrade to 05.xx.xx before installing 06.02.00-22.

Upgrades and downgrades are supported only from one major release to the next,

such as from 05.xx.xx to 06.02.00-22. If EWS is used for upgrades and

downgrades, and this rule is not followed, errors occur and there may be a

disruption to attached devices.

If upgrading to firmware 06.02.00-22 requires you to upgrade from 04.xx.xx to

05.xx.xx in the process, there are special considerations, as detailed in the section,

"Upgrading firmware on an edge switch from 04.xx.xx to

A small number of early-shipped Surestore Director FC-64 units may receive one

of the following messages when they upgrade to firmware 05.02.00-13:

This occurs only in certain units with CTP cards. Units with CTP2 cards do not

have this issue.

If you get one of these messages during the upgrade, the firmware upgrade failed,

but the unit continues working with the existing firmware without an interruption

in service. The upgrade process checks for sufficient memory before activating the

new firmware image. The firmware upgrade does not complete without sufficient

memory. Please contact HP Customer Support if you receive this message.

Upgrading firmware on an edge switch from 04.xx.xx to 05.xx.xx

An issue has been identified in release 04.xx.xx if the contents of the nonvolatile

storage (NVRAM) on the CTP become corrupted. Once the configuration has

been loaded, this corruption is not detected until an IPL/IML, power cycle, or

firmware code load. If the NVRAM in the CTP has corrupted contents, the

firmware load can cause the configuration to reset to factory defaults, which could

cause a system outage.

HAFM—Firmware cannot be loaded due to insufficient

CTP memory.

EWS—File System Error: Insufficient memory for new

firmware version.

05.xx.xx" on page 10.

HP StorageWorks Edge Switch release notes