AQUATECH Flash Housing 사용자 설명서 - 페이지 2

{카테고리_이름} AQUATECH Flash Housing에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AQUATECH Flash Housing 2 페이지.

페이지 인쇄

AquaTech Pocket Wizard

OVERVIEW

The AquaTech Pocket Wizard housing allows you to use your Pocket Wizard in and around

the water. Based on the cable used inside your housing, it can either

• Fire strobes remotely (using PC Sync cable)

Depending on your objective and version of your housing, your housing may require rewiring

by AquaTech to enable full functionality. This involves rewiring so that either the PC Sync cable

or Cable release may be connected.

FEATURES

Pocket Wizard Housing – clear housing that protects the Pocket Wizard

Flash Hotshoe – where Pocket Wizard attaches to housing

Antenna Gland – a double o-ring path for the Antenna to exit the Housing

Flash mount – Mount that attaches to top of your housing using 2 screws (M5 x 10)

3.5mm minijack – cable connecting the Pistol Bulkhead to the Pocket Wizard

PW Bulkhead – waterproof female connector that connects the outside cable to the Minijack wiring

Inline Cable – waterproof cable that connects the camera housing bulkhead and PW Bulkhead

PC Sync Cable – a cable that connects your camera housing's bulkhead to the camera's

Flash Sync output; used to fire strobes remotely

Cable release – a cable that connects your housing bulkhead to the camera's

Cable Release input; used to fire camera remotely

COnnECTIOn

Camera ➞ PC Sync Cable (or Cable Release) ➞ Housing Bulkhead ➞ Inline Cable ➞

PW Bulkhead ➞ 3.5mm Minijack ➞ Pocket Wizard

ImPORTAnT

1) Most Pocket Wizards cannot transmit/receive a signal underwater.

Thus, the Pocket Wizard housing must float at the surface to work properly.

2) AquaTech Sport Housings cannot accommodate the PC Sync cable as shipped and

thus will require custom wiring by AquaTech. To fire the camera remotely, you should

not require rewiring if your housing has a cable release hardwired inside.

Please contact us with any questions.

3) If you are having trouble fitting the antenna through the gland, use the grease from your

housing kit (or any silicone based grease) to lubricate

Page 2

• Remotely fire the camera

(using Cable Release)

AquaTech Flash Housing

OVERVIEW

The AquaTech Flash Housing allows you to use your professional Canon or Nikon flash in and

around the water. These housings have been control tested and water tested down to a depth

of 10m (30 feet). Full controls of the flash on the backplate enable you to change settings

while in the water.

FEATURES

Flash Housing – clear housing that protects your flash

Flash Clips – used to secure the Flash Housing's backplate

Piston Style O-ring – seals on the side wall of the backplate

Flash Hot Shoe – an electrical connector that secures the flash inside the Housing

Flash mount – a mount that attaches to your Sport Housing using 2 screws

Flash Bulkhead – a bulkhead that connects your Flash Hot Shoe to the Sync Cord

Sync Cord – a waterproof cable that connects the Flash Bulkheads on your Sport Housing

and Flash Housing. Includes caps for both ends.

Camera Hot Shoe cable – this cable connects to the inside of your Sport Housing's Flash

Bulkhead. It then plugs into the top of your camera on the hot shoe.

Release Tool – a small plastic key with a metal rod. It is used to help remove the backplate

off of the Flash Housing. The metal rod is inserted into holes on the flash housing and the

piece turns to gain leverage to push off backplate.

COnnECTIOn

Camera ➞ Camera Hot Shoe ➞ Housing Flash Bulkhead ➞ Sync Cord ➞ Flash Bulkhead ➞

Flash Hot Shoe ➞ Flash

ImPORTAnT

1) The Flash Bulkhead on both your Sport Housing and Flash Housing comes with a black cap.

It is important that, when not in use, this black cap be tightened firmly. Without this, the

system is not waterproof.

2) Take care with the Camera Hot Shoe and the connection to the Flash Bulkhead – it is fragile.

Page 3