HP ProCurve 1600M 먼저 읽기 - 페이지 7

{카테고리_이름} HP ProCurve 1600M에 대한 먼저 읽기을 온라인으로 검색하거나 PDF를 다운로드하세요. HP ProCurve 1600M 8 페이지. Redundant power supply
HP ProCurve 1600M에 대해서도 마찬가지입니다: 사양 시트 (12 페이지), 검토자 매뉴얼 (27 페이지), 보충 설명서 (2 페이지), 보충 설명서 (2 페이지), 설치 매뉴얼 (28 페이지), 설치 매뉴얼 (36 페이지), 설치 매뉴얼 (28 페이지), 빠른 설정 매뉴얼 (2 페이지), 빠른 설정 매뉴얼 (4 페이지), 사용자 설명서 (8 페이지), 매뉴얼 보충 자료 (28 페이지), 먼저 읽기 (16 페이지), 설치 및 제거 (2 페이지), 설치 매뉴얼 (12 페이지), 계획 및 구현 매뉴얼 (40 페이지), 제품 수명이 다한 제품 분해 지침 (2 페이지), 설치 매뉴얼 (46 페이지), 진단 매뉴얼 (2 페이지), 분해 지침 (2 페이지)

Solution. A routing switch allows only one session of the Web management interface at any given time. Thus, if one

user is accessing the routing switch via the Web, the not available or in use messages will appear to another user who

is trying to access that routing switch through the Web management interface. You can, however, limit access via the

Web management interface by assigning a password to the routing switch. With a password set, access via the Web

management interface will be available only to users who can enter the password. For more on passwords, refer to

the Installation and Configuration Guide you received with the routing switch.

Device Will Not Boot Up Due to Corrupt Operating System

Condition. The operating system (OS) is corrupt on both the primary and secondary flash memory, and the routing

switch will not boot up.

Solution. The routing switch will first try to boot up using the primary OS written to flash memory. If this fails, the

device automatically tries to boot from the secondary flash memory. If this also fails, the routing switch then tries to

connect to a TFTP server and boot from there. This will fail if a TFTP server is not configured to support the routing

switch, or is not found. You can perform this solution only if you have access to a TFTP server. Otherwise, there are

TFTP applications (available on the World Wide Web) that you can use to enable your PC to appear as a TFTP server

to the routing switch. One website where such software can be found is http://www.walusoft.co.uk.

Using a straight-through cable, directly connect a PC or terminal to the serial port on the routing switch. (For

more information on attaching a PC or terminal, refer to chapter 2, "Installation", in the Installation and

Configuration Guide.)

Reboot the routing switch.

While the system is booting up, enter b at the CLI to go into the boot monitor mode.

Enter the following commands:

boot> ip address <ip address> <subnet mask>

boot> ip default_gateway <ip address of tftp server --or-- default gateway to get to tftp server>

boot> boot system tftp <ip address of tftp server> <configuration file name>

The routing switch will now be able to boot up over the network. a new copy of the operating system can now be

downloaded to the primary and secondary flash memories via the TFTP server.