HP StorageWorks 1000 - Modular Smart Array 교체 지침

{카테고리_이름} HP StorageWorks 1000 - Modular Smart Array에 대한 교체 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. HP StorageWorks 1000 - Modular Smart Array 4 페이지. Power supply, computer
HP StorageWorks 1000 - Modular Smart Array에 대해서도 마찬가지입니다: 네트워크 매뉴얼 (8 페이지), 지원 목록 (34 페이지), 오류 방지 매뉴얼 (12 페이지), 기술 백서 (12 페이지), 펌웨어 업데이트 (9 페이지), 개요 (20 페이지), 설치 매뉴얼 (2 페이지), 지원 전화번호 (19 페이지), 참조 매뉴얼 (48 페이지), 관리 매뉴얼 (40 페이지), 릴리스 노트 (13 페이지), 빠른 시작 지침 (8 페이지), 빠른 시작 매뉴얼 (7 페이지), 릴리스 노트 (5 페이지), 백서 (13 페이지), 기술 개요 (15 페이지), 빠른 사양 (17 페이지), 사양 (49 페이지), 시작하기 매뉴얼 (34 페이지), 설치 (4 페이지), 설치 매뉴얼 (18 페이지), 분해 지침 매뉴얼 (9 페이지), 프로그래밍 매뉴얼 (8 페이지)

페이지 인쇄
HP StorageWorks 1000 - Modular Smart Array 교체 지침
HP StorageWorks
Modular Smart Array
controller, cache, and battery
replacement instructions
These instructions apply to MSA1000,
MSA1500 cs, and MSA1510i products.
These components may also be used in other
HP products. See documentation for your
specific product for replacement instructions.
© Copyright 2005-2006 Hewlett-Packard Development Company, L.P.
Second edition February 2006
Product names mentioned herein may be trademarks of their respective
companies as reflected by an associated footnote.
Information in this document is subject to change without notice.
Printed in the US.
www.hp.com
*383078-002*
383078–002
About this document
This document details procedures for replacing a controller, controller
cache module, or cache batteries in HP StorageWorks Modular Smart
Array (MSA) 1000, 1500 cs, and 1510i products.

Before you begin

CAUTION:
Be sure the replacement is available before removing
the failed component. Removing a component impacts airflow and
cooling within the enclosure.
CAUTION:
Follow these instructions when replacing components.
If the procedure is done improperly, it is possible to lose data or
damage equipment.
CAUTION:
When handling system components, there is a
danger to equipment from electrostatic discharge (ESD). Use proper
anti-static protection at all times:
•
Keep the replacement component in the ESD bag until needed.
•
Wear an ESD wrist strap grounded to an unpainted surface of the
chassis.
•
If an ESD wrist strap is unavailable, touch an unpainted surface of
the chassis before handling the component.
•
Never touch connector pins.
See your user documentation for additional information.
Using this document
Your replacement procedures may not require all steps listed in this
document.
•
Controller replacement—Use steps 1, 2, 4, and 5.
•
Controller cache module replacement—Use steps 1, 2, 4, and 5.
•
Controller cache battery replacement—Use steps 1, 2, 3, 4, and 5.

Verifying component failure

Before replacing a controller, cache module, or battery pack:
•
Check the controller heartbeat LED (1).
If the LED is not blinking, it might indicate a failure.
•
Check the controller fault LED (2).
If the LED is on, it might indicate a failure. Check for an error
message listed in
Table 1
•
Remove the controller, wait 10 seconds, and then reinsert it,
ensuring that it is fully seated in the chassis. If this does not resolve
the issue, continue with the replacement procedures.
Figure 1
MSA controller
and take appropriate action.
1
2
15192