HP StorageWorks XP12000 사용자 설명서 - 페이지 20

{카테고리_이름} HP StorageWorks XP12000에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. HP StorageWorks XP12000 30 페이지. Cache lun xp
HP StorageWorks XP12000에 대해서도 마찬가지입니다: 릴리스 노트 (13 페이지), 관리자 매뉴얼 (50 페이지), 구성 매뉴얼 (42 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (36 페이지), 구성 매뉴얼 (36 페이지), 구성 매뉴얼 (30 페이지), 구성 매뉴얼 (36 페이지), 릴리스 노트 (5 페이지), 시스템 구성 매뉴얼 (49 페이지), 시스템 구성 매뉴얼 (43 페이지), 시스템 구성 매뉴얼 (42 페이지), 시스템 구성 매뉴얼 (35 페이지), 구성 매뉴얼 (46 페이지), 구성 매뉴얼 (46 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (44 페이지), 구성 매뉴얼 (38 페이지), 구성 매뉴얼 (34 페이지), 구성 매뉴얼 (30 페이지), 구성 매뉴얼 (30 페이지), 구성 매뉴얼 (42 페이지), 구성 매뉴얼 (50 페이지)

For open systems, Cache LUN XP identifies a logical area in units of 128 blocks for OPEN-V, and

96 blocks for other than OPEN-V. For OPEN-V, if you have entered 1 as the starting logical block

address and a value less than 128 as the ending logical block address, Cache LUN XP

automatically changes the ending block address to 128. For other than OPEN-V, if you have

entered 1 as the starting logical block address and a value less than 96 as the ending logical block

address, Cache LUN XP automatically changes the ending block address to 96.

c. Select the Multi Set / Release check box.

d. Click Set. A confirmation dialog box appears.

e. Click OK to continue. The Multi Set pane appears.

f. In the CU drop-down list, click the CU.

g. In the table, click more than one LDEV and then click Set. The Multi Set pane closes and the new

settings are shown in blue on the Cache LUN pane. To cancel operations, click Cancel. Go to

step

10.

10.To make data in other volumes reside in the Cache LUN XP cache, repeat the previous steps.

NOTE:

11.To enable the pre-staging function, select the Prestaging check box. To disable the pre-staging function,

clear the Prestaging check box.

12.If the settings are correct, click Apply. A confirmation dialog box appears.

13.Click OK to confirm. The Cache LUN XP operation begins. If prestaging was selected, the prestaging

operation will occur next. When the operation has been completed, a confirmation dialog box

appears.

14.Click OK.

Releasing (removing) a cache extent

In the LDEV tree of the Cache LUN pane, click the CU:LDEV number of the LDEV you want to remove

from cache. The LDEV table displays Cache LUN XP information about the LDEV you selected.

Select an extent to be removed from the Cache LUN XP cache. The Release button is enabled.

Complete one of the following steps:

• To remove specific data from cache, go to

• To remove all data from cache, go to

To remove specific data from cache:

a. Click Release. A confirmation dialog box appears.

b. Click OK to continue. The new settings are shown in blue on the Cache LUN pane. To cancel

operations, click Cancel. Go to

To remove all data from cache

a. Select the Multi Set / Release check box.

b. Click Release. A confirmation dialog box appears.

Cache LUN XP for the XP10000/XP12000

You cannot use the Release button to delete the set data until you click Apply or Cancel.

step